How to replace the wiper motor and windshield washer reservoir or washer pump on Ford Taurus?

As of 2008 models, start by disconnecting the battery's negative terminal cable. Note down where the wiper arms connect to the linkage shafts. Then you can remove their nuts. Start by unscrewing the plastic cowl covering, and get rid of the three bolts that connect the wiper linkage piece. Pull up slightly to separate the electric connector, then take away entire wiper-bulge assembly, including hard parts. Pull out the three bolts that hold the motor and the metal bar on the linkage arm. Take care to have the motor in the parking position before taking out the metal bar. Use your trim removal tool or screwdriver to carefully pull the linkage away from the motor's crank arm. Put the new motor back on the linkage, make sure all the bolts are tight, connect the electricity correctly, all the while keeping tools and extra stuff away. Before removing anything else, rotate the wipers with the ignition on so the motor moves to its parking position. After putting everything back in its place, adjust the wiper arms: position the passenger blade 1.5 inches high and the driver's blade 2 inches high. Hit the switch once more to view how well the wipers align. Adjust them if needed. To get at the washer reservoir or pump for replacement, take off the lower front air deflector shield and right side inner fender splash shield. Pull off the fluid sensor and washer pump connections, then unplug the washer pump and let the tank empty of fluid. Take off the bottom screw holding the reservoir, the two round washers, and then carefully lift the reservoir directly from below. If the washer pump needs replacing, remove the damaged rubber grommet that keeps it in place along the tank. Installation is the reverse of removal.

Genuine Ford Taurus Washer Pump

Windshield Washer Pump

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

7 Washer Pumps found

View related parts
Ford Taurus Motor And Pump Assembly
Part Number: 8G1Z-17664-A
$58.96 MSRP: $80.57
You Save: $21.61 (27%)
ADD TO CART
Product Specifications
- Other Name: Motor And Pump Assy
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2008-2019 Ford Taurus | 4 Cyl 2.0L EcoBoost (240PS) , 6 Cyl 3.5L Cyclone Petrol TIVCT, 6 Cyl 3.5L DOHC T/C, 6 Cyl 3.5L DOHC VCT SMPI, 6 Cyl 3.7L DOHC | 6-Speed Automatic Transaxle - AWF21, 6-Speed Automatic Transmission 6F Mid-Range, 6-Speed Automatic Transmission 6F50, 6-Speed Automatic Transmission 6F55, CVT Select Shift Transmission, Four-Wheel Drive (Full Time) (Left Hand Drive), Four-Wheel Drive (Part Time) (Left Hand Drive), Front-Wheel Drive (Left Hand Drive), Left Hand Drive
View related parts
Ford Taurus Motor And Pump Assembly
Part Number: 6F1Z-17664-A
$30.23 MSRP: $42.91
You Save: $12.68 (30%)
Ships in 1 Business Day
ADD TO CART
Product Specifications
- Other Name: Motor And Pump Assy
- Manufacturer Note: Submersible-terminals covered, windshield reservoir
- Replaced by: 7R3Z-17664-A
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2006-2007 Ford Taurus | 6 Cyl 3.0L | 4AT 4F50N
View related parts
Ford Taurus Motor And Pump Assembly
Part Number: JL3Z-17664-A
$48.82 MSRP: $79.09
You Save: $30.27 (39%)
Ships in 1 Business Day
ADD TO CART
Product Specifications
- Other Name: Motor And Pump Assy; Washer Pump
- Replaces: GR2Z-17664-A
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2019 Ford Taurus | 4 Cyl 2.0L EcoBoost (240PS) , 6 Cyl 3.5L Cyclone Petrol TIVCT, 6 Cyl 3.5L DOHC T/C, 6 Cyl 3.7L DOHC | 6-Speed Automatic Transmission 6F Mid-Range, 6-Speed Automatic Transmission 6F50, 6-Speed Automatic Transmission 6F55, Four-Wheel Drive (Full Time) (Left Hand Drive), Four-Wheel Drive (Part Time) (Left Hand Drive), Front-Wheel Drive (Left Hand Drive), Left Hand Drive
View related parts
Ford Taurus Motor And Pump Assembly
Part Number: EOAZ-17664-A
$175.23 MSRP: $296.36
You Save: $121.13 (41%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Motor And Pump Assy; Front Washer Pump, Pump, Washer Pump
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 1986-2007 Ford Taurus | 4 Cyl 2.5L, 6 Cyl 3.0L, 6 Cyl 3.2L, 6 Cyl 3.8L, 8 Cyl 3.4L | 3AT ATX, 4AT 4F50N, 4AT AX4N, 4AT AX4S, 4AT AXOD, 4AT AXOD-E, 5MT
View related parts
Ford Taurus Motor And Pump Assembly
Part Number: E5TZ-17664-B
$21.29 MSRP: $33.09
You Save: $11.80 (36%)
Product Specifications
- Other Name: Motor And Pump Assy
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 1986-2007 Ford Taurus | 4 Cyl 2.5L, 6 Cyl 3.0L, 6 Cyl 3.2L, 6 Cyl 3.8L, 8 Cyl 3.4L | 3AT ATX, 4AT 4F50N, 4AT AX4N, 4AT AX4S, 4AT AXOD, 4AT AXOD-E, 5MT
View related parts
Ford Taurus Motor And Pump Assembly
Part Number: F6SZ-17664-DA
Product Specifications
- Other Name: Motor And Pump Assy
- Replaces: F6SZ-17664-CA, F7ZZ-14290-AA
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 1996-2001 Ford Taurus | 6 Cyl 3.0L, 8 Cyl 3.4L | 4AT 4F50N, 4AT AX4N, 4AT AX4S
View related parts
Ford Taurus Motor And Pump Assembly
Part Number: F6SZ-17664-CA
Product Specifications
- Other Name: Motor And Pump Assy
- Replaced by: F6SZ-17664-DA
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 1996 Ford Taurus | 6 Cyl 3.0L, 8 Cyl 3.4L | 4AT AX4N, 4AT AX4S

Ford Taurus Washer Pump

The Ford Taurus Washer Pump helps to keep the windshield clean by pushing windshield cleaning fluid through the nozzles onto the windshield to allow for a clear view of the road. Every Ford system uses a tiny electric motor to spin an impeller that pressurizes fluid in the reservoir. Tubing sends the spray to the wiper area to quickly remove dirt. In the Taurus automobiles, the Washer Pump is located at the bottom of the tank, which helps keep it primed due to gravity. When the driver taps the stalk switch, quick washer jets are activated. Older Taurus versions placed the Washer Pump outside the tank, while later Ford versions mold it directly into the reservoir. The design is basically the same, but each Ford unit can have simple wiring that is plug-and-swap and flows similarly to that of other units. In the event of a Washer Pump failure, symptoms include silence or weak spray. The cost of components is low, while labor generally adds a little, making the Taurus Washer Pump affordable to maintain.

We provide a wide range of Ford Taurus Washer Pump at the optimal prices. If you need Ford Taurus Washer Pump, you can shop with confidence on our website. All our OEM parts come with a manufacturer's warranty and are delivered to your doorstep with a fast delivery service.

Ford Taurus Washer Pump Parts Questions & Experts Answers

Motor And Pump Assembly
8G1Z-17664-A
Q: How to replace the wiper motor and windshield washer reservoir or washer pump on Ford Taurus?
A:
As of 2008 models, start by disconnecting the battery's negative terminal cable. Note down where the wiper arms connect to the linkage shafts. Then you can remove their nuts. Start by unscrewing the plastic cowl covering, and get rid of the three bolts that connect the wiper linkage piece. Pull up slightly to separate the electric connector, then take away entire wiper-bulge assembly, including hard parts. Pull out the three bolts that hold the motor and the metal bar on the linkage arm. Take care to have the motor in the parking position before taking out the metal bar. Use your trim removal tool or screwdriver to carefully pull the linkage away from the motor's crank arm. Put the new motor back on the linkage, make sure all the bolts are tight, connect the electricity correctly, all the while keeping tools and extra stuff away. Before removing anything else, rotate the wipers with the ignition on so the motor moves to its parking position. After putting everything back in its place, adjust the wiper arms: position the passenger blade 1.5 inches high and the driver's blade 2 inches high. Hit the switch once more to view how well the wipers align. Adjust them if needed. To get at the washer reservoir or pump for replacement, take off the lower front air deflector shield and right side inner fender splash shield. Pull off the fluid sensor and washer pump connections, then unplug the washer pump and let the tank empty of fluid. Take off the bottom screw holding the reservoir, the two round washers, and then carefully lift the reservoir directly from below. If the washer pump needs replacing, remove the damaged rubber grommet that keeps it in place along the tank. Installation is the reverse of removal.