How to install a Trunk Latch and Trunk Lock Cylinder in the trunk lid on a Ford Taurus?

In order to replace the key lock cylinder, to put the new rivets in the door one needs a special rivet installation tool. Start with the pull-down strap fasteners and the strap and then pry the pin type fasteners with a plastic trim tool and then pull out the trunk lid trim panel. Finally, some irregularities may occur when the trunk lid actuator cable is removed from the key lock cylinder, and the electrical connector disconnected from the lock cylinder is removed. Two rivets are to be drilled out separating the lock cylinder and it should be pulled out. For reinstallctions, removal should be done in the reverse order that they were done in. For the latch start with the removal of the trim panel and then you will have to unplug the electrical connectors of the trunk lid latch. After that, it is necessary to remove the latch mounting nuts and then the latch itself is to be removed. As mentioned earlier, reinstallation has to be done from right from the bottom and has to progress upwards in a sequential manner, that is, a process that is almost similar to that of removal in reverse.

Genuine Ford Taurus Trunk Lock Cylinder

Back Door Cylinder

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

3 Trunk Lock Cylinders found

View related parts
Ford Taurus Lock Cylinder Assembly
Part Number: 6R3Z-6343262-A
$150.35 MSRP: $233.10
You Save: $82.75 (36%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Cylinder Assy - Lock; Lock Cylinder, Lock Cylinder Assembly
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2013-2019 Ford Taurus | 4 Cyl 2.0L EcoBoost (240PS) , 6 Cyl 3.5L Cyclone Petrol TIVCT, 6 Cyl 3.5L DOHC T/C, 6 Cyl 3.7L DOHC | 6-Speed Automatic Transmission 6F Mid-Range, 6-Speed Automatic Transmission 6F50, 6-Speed Automatic Transmission 6F55, Four-Wheel Drive (Full Time) (Left Hand Drive), Four-Wheel Drive (Part Time) (Left Hand Drive), Front-Wheel Drive (Left Hand Drive), Left Hand Drive
View related parts
Ford Taurus Lock Cylinder Assembly
Part Number: 6R3Z-6343262-B
$192.57 MSRP: $281.53
You Save: $88.96 (32%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Cylinder Assembly - Lock; Lock Cylinder, Lock Cylinder Assembly
- Replaces: 5W4Z-5443262-BB
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2013-2019 Ford Taurus | 4 Cyl 2.0L EcoBoost (240PS) , 6 Cyl 3.5L Cyclone Petrol TIVCT, 6 Cyl 3.5L DOHC T/C, 6 Cyl 3.7L DOHC | 6-Speed Automatic Transmission 6F Mid-Range, 6-Speed Automatic Transmission 6F50, 6-Speed Automatic Transmission 6F55, Four-Wheel Drive (Full Time) (Left Hand Drive), Four-Wheel Drive (Part Time) (Left Hand Drive), Front-Wheel Drive (Left Hand Drive), Left Hand Drive
View related parts
Ford Taurus Lock Cylinder Assembly
Part Number: 1F1Z-5443262-CA
Product Specifications
- Other Name: Cylinder Assy - Lock
- Manufacturer Note: Luggage compartment, w/o anti-theft
- Replaced by: 5F1Z-5443262-CA
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2008-2009 Ford Taurus | 6 Cyl 3.5L DOHC VCT SMPI | 6-Speed Automatic Transaxle - AWF21, 6-Speed Automatic Transmission 6F50, CVT Select Shift Transmission, Four-Wheel Drive (Part Time) (Left Hand Drive), Front-Wheel Drive (Left Hand Drive), Left Hand Drive
- 2002-2005 Ford Taurus | 6 Cyl 3.0L | 4AT 4F50N, 4AT AX4S

Ford Taurus Trunk Lock Cylinder

The Ford Taurus Trunk Lock Cylinder provides an easy, reliable way to lock the rear cargo area against theft. When the key is inserted and turned, the Trunk Lock Cylinder causes a metal cam to spin that grabs the latch to pull the deck lid tight so it remains shut until the matching key releases it to keep tools, luggage, and the spare tire secure. This is a purely mechanical component that gives an instant response, unlike any electronic buttons that usually fail to work once its battery dies. Ford chose to keep a single durable steel Trunk Lock Cylinder design through every generation of Ford Taurus produced. This commonality of function means early nineties sedans and later Taurus wagons work with the same smooth quarter-turn. The absence of alternative style in the records means replacement pays attention to condition and not type. By wiping the grit from the keyway regularly and adding a light spray of graphite, the Trunk Lock Cylinder clicks and rotates smoothly. This small component allows every Ford owner to close their Taurus trunk with confidence every time, knowing the Trunk Lock Cylinder will protect their cargo year after year.

We provide a wide range of Ford Taurus Trunk Lock Cylinder at the optimal prices. If you need Ford Taurus Trunk Lock Cylinder, you can shop with confidence on our website. All our OEM parts come with a manufacturer's warranty and are delivered to your doorstep with a fast delivery service.

Ford Taurus Trunk Lock Cylinder Parts Questions & Experts Answers

Lock Cylinder Assembly
6R3Z-6343262-A
Q: How to install a Trunk Latch and Trunk Lock Cylinder in the trunk lid on a Ford Taurus?
A:
In order to replace the key lock cylinder, to put the new rivets in the door one needs a special rivet installation tool. Start with the pull-down strap fasteners and the strap and then pry the pin type fasteners with a plastic trim tool and then pull out the trunk lid trim panel. Finally, some irregularities may occur when the trunk lid actuator cable is removed from the key lock cylinder, and the electrical connector disconnected from the lock cylinder is removed. Two rivets are to be drilled out separating the lock cylinder and it should be pulled out. For reinstallctions, removal should be done in the reverse order that they were done in. For the latch start with the removal of the trim panel and then you will have to unplug the electrical connectors of the trunk lid latch. After that, it is necessary to remove the latch mounting nuts and then the latch itself is to be removed. As mentioned earlier, reinstallation has to be done from right from the bottom and has to progress upwards in a sequential manner, that is, a process that is almost similar to that of removal in reverse.