How to remove and install the oil pan in four cylinder engine on Ford Taurus?

To remove the components, first raise the vehicle and support it securely on jackstands. Drain the engine oil, clean and install the engine oil drain plug, and remove and discard the oil filter for replacement. Next, remove the lower engine splash shield and the air filter housing. The transaxle must be moved slightly back from the engine, so support the engine from above and the transaxle with a floor jack. Loosen the upper engine-to-transaxle mounting bolts and back them off about 0.20 inch (5 mm), then loosen the left-side and right-side engine-to-bellhousing bolts. Caution is advised as the transaxle should not be moved back more than 0.20 inch (5 mm) to avoid damage. Remove the transaxle roll restrictor mount through bolts and the mount itself, followed by the catalytic converter. Next, remove the three bellhousing-to-pan bolts, one oil pan-to-bellhousing bolt, and the timing chain cover-to-oil pan fasteners. Move the power steering hose away from the oil pan by removing the bracket retaining nut, and then remove the air conditioning compressor without disconnecting the lines. Use a screwdriver to pry between the engine and transaxle until the bellhousing has moved away from the block to the limit of the loosened bolts. Unscrew the oil pan retaining bolts evenly until all are removed, then use a rubber mallet to loosen the oil pan seal and lower the oil pan, turning it as necessary to clear the exhaust system. Be cautious when prying between mating surfaces to avoid damage that could lead to leaks, and use a putty knife to cut through any sealant if necessary. For installation, thoroughly clean and degrease the mating surfaces of the lower engine block/crankcase and oil pan, removing all traces of sealant, and wipe out the oil pan. Apply a 1/8-inch wide bead of sealant to the oil pan flange, ensuring it is approximately 3/16-inch from the outside edge and around the inside edge of the bolt holes, as well as to the front flange where it meets the timing chain cover. The oil pan must be installed within 10 minutes of applying the sealant. Install the oil pan bolts, tightening them finger tight, followed by the timing chain cover-to-oil pan fasteners to the specified torque. Tighten the oil pan-to-engine block bolts in a circular pattern from the center outwards to the specified torque, then tighten the oil pan-to-bellhousing bolts and the transaxle to engine bolts evenly to the specified torque. Finally, lower the vehicle to the ground and wait at least 1 hour for the sealant to cure before refilling the engine with oil, trimming off any excess sealant with a sharp knife, and installing a new oil filter.

Genuine Ford Taurus Oil Pan

Oil Drain Pan

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

25 Oil Pans found

View related parts
Ford Taurus Engine Oil Pan Assembly
Part Number: 7T4Z-6675-A
$137.94 MSRP: $201.67
You Save: $63.73 (32%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Pan Assy - Engine Oil; Oil Pan
- Manufacturer Note: Use RTV Silicone Sealer In Place Of Gasket For This Application. Refer To Workshop Manual For Specification
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2008-2012 Ford Taurus | 6 Cyl 3.5L DOHC VCT SMPI | 6-Speed Automatic Transaxle - AWF21, 6-Speed Automatic Transmission 6F Mid-Range, 6-Speed Automatic Transmission 6F50, 6-Speed Automatic Transmission 6F55, CVT Select Shift Transmission, Four-Wheel Drive (Full Time) (Left Hand Drive), Four-Wheel Drive (Part Time) (Left Hand Drive), Front-Wheel Drive (Left Hand Drive), Left Hand Drive
View related parts
Ford Taurus Engine Oil Pan Assembly
Part Number: CJ5Z-6675-A
$183.70 MSRP: $278.33
You Save: $94.63 (34%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Pan Assy - Engine Oil
- Manufacturer Note: Use RTV Silicone Sealer In Place Of Gasket For This Application. Refer To Workshop Manual For Specification
- Replaced by: CJ5Z-6675-G
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2013-2019 Ford Taurus | 4 Cyl 2.0L EcoBoost (240PS) | 6-Speed Automatic Transmission 6F Mid-Range, 6-Speed Automatic Transmission 6F50, 6-Speed Automatic Transmission 6F55, Four-Wheel Drive (Full Time) (Left Hand Drive), Four-Wheel Drive (Part Time) (Left Hand Drive), Front-Wheel Drive (Left Hand Drive), Left Hand Drive
View related parts
Ford Taurus Engine Oil Pan Assembly
Part Number: DG1Z-6675-F
$109.78 MSRP: $160.50
You Save: $50.72 (32%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Pan Assy - Engine Oil; Oil Pan
- Replaces: DG1Z-6675-E, DG1Z-6675-D
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2013-2019 Ford Taurus | 6 Cyl 3.5L Cyclone Petrol TIVCT, 6 Cyl 3.7L DOHC | 6-Speed Automatic Transmission 6F Mid-Range, 6-Speed Automatic Transmission 6F50, 6-Speed Automatic Transmission 6F55, Four-Wheel Drive (Full Time) (Left Hand Drive), Four-Wheel Drive (Part Time) (Left Hand Drive), Front-Wheel Drive (Left Hand Drive), Left Hand Drive
View related parts
Ford Taurus Engine Oil Pan Assembly
Part Number: BG1Z-6675-E
$157.32 MSRP: $230.00
You Save: $72.68 (32%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Pan Assy - Engine Oil; Oil Pan
- Replaces: BG1Z-6675-D, BG1Z-6675-C
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2013-2019 Ford Taurus | 6 Cyl 3.5L DOHC T/C | 6-Speed Automatic Transmission 6F Mid-Range, 6-Speed Automatic Transmission 6F50, 6-Speed Automatic Transmission 6F55, Four-Wheel Drive (Full Time) (Left Hand Drive), Four-Wheel Drive (Part Time) (Left Hand Drive), Front-Wheel Drive (Left Hand Drive), Left Hand Drive
View related parts
Ford Taurus Engine Oil Pan Assembly
Part Number: DG1Z-6675-E
$109.78 MSRP: $160.50
You Save: $50.72 (32%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Pan Assy - Engine Oil
- Manufacturer Note: Use RTV Silicone Sealer In Place Of Gasket For This Application. Refer To Workshop Manual For Specification
- Replaced by: DG1Z-6675-F
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2013-2019 Ford Taurus | 6 Cyl 3.5L Cyclone Petrol TIVCT | 6-Speed Automatic Transmission 6F Mid-Range, 6-Speed Automatic Transmission 6F50, 6-Speed Automatic Transmission 6F55, Four-Wheel Drive (Full Time) (Left Hand Drive), Four-Wheel Drive (Part Time) (Left Hand Drive), Front-Wheel Drive (Left Hand Drive), Left Hand Drive
View related parts
Ford Taurus Engine Oil Pan Assembly
Part Number: F5DZ-6675-CA
$68.22 MSRP: $93.22
You Save: $25.00 (27%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Pan Assy - Engine Oil; Oil Pan
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 1995 Ford Taurus | 6 Cyl 3.8L | 4AT AX4N, 4AT AX4S, 4AT AXOD-E, 5MT
View related parts
Ford Taurus Engine Oil Pan Assembly
Part Number: 2F1Z-6675-BA
$198.71 MSRP: $276.04
You Save: $77.33 (29%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Pan Assy - Engine Oil; Oil Pan
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2002-2007 Ford Taurus | 6 Cyl 3.0L | 4AT 4F50N, 4AT AX4S
View related parts
Ford Taurus Engine Oil Pan Assembly
Part Number: XF2Z-6675-EA
$50.45 MSRP: $68.93
You Save: $18.48 (27%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Pan Assy - Engine Oil; Oil Pan
- Manufacturer Note: 12V
- Replaces: F68Z-6675-BA
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 1996-2001 Ford Taurus | 6 Cyl 3.0L | 4AT 4F50N, 4AT AX4N, 4AT AX4S
View related parts
Ford Taurus Engine Oil Pan Assembly
Part Number: F68Z-6675-BA
$50.45 MSRP: $68.93
You Save: $18.48 (27%)
ADD TO CART
Product Specifications
- Other Name: Pan Assy - Engine Oil
- Replaced by: XF2Z-6675-EA
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 1996-1999 Ford Taurus | 6 Cyl 3.0L | 4AT AX4N, 4AT AX4S
View related parts
Ford Taurus Engine Oil Pan Assembly
Part Number: AA5Z-6675-J
Product Specifications
- Other Name: Pan Assy - Engine Oil; Oil Pan
- Replaces: AA5Z-6675-H
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2010-2012 Ford Taurus | 6 Cyl 3.5L DOHC T/C | 6-Speed Automatic Transmission 6F Mid-Range, 6-Speed Automatic Transmission 6F50, 6-Speed Automatic Transmission 6F55, Four-Wheel Drive (Full Time) (Left Hand Drive), Four-Wheel Drive (Part Time) (Left Hand Drive), Front-Wheel Drive (Left Hand Drive), Left Hand Drive
View related parts
Ford Taurus Engine Oil Pan Assembly
Part Number: F33Z-6675-A
Product Specifications
- Other Name: Pan Assy - Engine Oil; Oil Pan
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 1986-1990 Ford Taurus | 4 Cyl 2.5L, 6 Cyl 3.0L, 6 Cyl 3.8L | 3AT ATX, 4AT AX4S, 4AT AXOD, 5MT
View related parts
Ford Taurus Engine Oil Pan Assembly
Part Number: F7DZ-6675-AA
Product Specifications
- Other Name: Pan Assy - Engine Oil
- Replaced by: 3F1Z-6675-DA
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 1997-2003 Ford Taurus | 6 Cyl 3.0L | 4AT 4F50N, 4AT AX4N, 4AT AX4S
View related parts
Ford Taurus Pan Assembly Transmission O
Part Number: F6DZ7A194D
Product Specifications
- Other Name: Pan Assy - Transmission Oil
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 1996 Ford Taurus | 6 Cyl 3.0L, 8 Cyl 3.4L | 4AT AX4N, 4AT AX4S
View related parts
Ford Taurus Engine Oil Pan Assembly
Part Number: F68Z-6675-AB
Product Specifications
- Other Name: Pan Assy - Engine Oil; Oil Pan
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 1988-1989 Ford Taurus | 4 Cyl 2.5L, 6 Cyl 3.0L, 6 Cyl 3.8L | 3AT ATX, 4AT AXOD, 5MT
View related parts
Ford Taurus Pan Assembly Engine Oil
Part Number: F5DZ6675A
Product Specifications
- Other Name: Pan Assy - Engine Oil; Oil Pan
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 1995 Ford Taurus | 6 Cyl 3.0L | 4AT AX4N, 4AT AX4S, 4AT AXOD-E, 5MT
View related parts
Ford Taurus Engine Oil Pan Assembly
Part Number: F4DZ-6675-B
Product Specifications
- Other Name: Pan Assy - Engine Oil
- Manufacturer Note: w/o low oil sensor
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 1994-1995 Ford Taurus | 6 Cyl 3.8L | 4AT AX4N, 4AT AX4S, 4AT AXOD-E, 5MT
View related parts
Ford Taurus Engine Oil Pan Assembly
Part Number: F4DZ-6675-A
Product Specifications
- Other Name: PAN ASY - ENGINE OIL
- Manufacturer Note: W/ low oil sensor
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 1990-1994 Ford Taurus | 6 Cyl 3.8L | 4AT AX4N, 4AT AX4S, 4AT AXOD, 4AT AXOD-E, 5MT
View related parts
Ford Taurus Engine Oil Pan Assembly
Part Number: F1SZ-6675-B
Product Specifications
- Other Name: Pan Assy - Engine Oil; Oil Pan
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 1986-1989 Ford Taurus | 4 Cyl 2.5L, 6 Cyl 3.0L, 6 Cyl 3.8L | 3AT ATX, 4AT AXOD, 5MT
View related parts
Ford Taurus Engine Oil Pan Assembly
Part Number: F1SZ-6675-A
Product Specifications
- Other Name: Pan Assy - Engine Oil; Oil Pan
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 1986-1989 Ford Taurus | 4 Cyl 2.5L, 6 Cyl 3.0L, 6 Cyl 3.8L | 3AT ATX, 4AT AXOD, 5MT
View related parts
Ford Taurus Pan Assembly Engine Oil
Part Number: E9DZ6675F
Product Specifications
- Other Name: Pan Assy - Engine Oil; Oil Pan
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 1986-1989 Ford Taurus | 4 Cyl 2.5L, 6 Cyl 3.0L, 6 Cyl 3.8L | 3AT ATX, 4AT AXOD, 5MT

| Page 1 of 2 |Next >

1-20 of 25 Results

Ford Taurus Oil Pan

The Oil Pan in Ford Taurus vehicles can be described as, An oil Pan is an engine oil tank and its main purpose is to hold and pump the oil that lubricates and cools the various parts of the engine. Using wet sump system, the Ford Taurus Oil Pan holds the oil that is drawn through a pickup tube by the oil pump, and circulates it in the engine and then returns it back to the pan. This design also provides continuous supply of oil which is regarded as crucial in the running of an engine. In the past, the Ford Taurus Oil Pans were often made of stamped steel, although, new technologies brought cast aluminum to most models that are more durable and efficient. The basic function of the grille stays the same however, these changes in material signify improvements in engineering and design to match the developments of the Ford Taurus model.

We provide a wide range of Ford Taurus Oil Pan at the optimal prices. If you need Ford Taurus Oil Pan, you can shop with confidence on our website. All our OEM parts come with a manufacturer's warranty and are delivered to your doorstep with a fast delivery service.

Ford Taurus Oil Pan Parts Questions & Experts Answers

Engine Oil Pan Assembly
CJ5Z-6675-A
Q: How to remove and install the oil pan in four cylinder engine on Ford Taurus?
A:
To remove the components, first raise the vehicle and support it securely on jackstands. Drain the engine oil, clean and install the engine oil drain plug, and remove and discard the oil filter for replacement. Next, remove the lower engine splash shield and the air filter housing. The transaxle must be moved slightly back from the engine, so support the engine from above and the transaxle with a floor jack. Loosen the upper engine-to-transaxle mounting bolts and back them off about 0.20 inch (5 mm), then loosen the left-side and right-side engine-to-bellhousing bolts. Caution is advised as the transaxle should not be moved back more than 0.20 inch (5 mm) to avoid damage. Remove the transaxle roll restrictor mount through bolts and the mount itself, followed by the catalytic converter. Next, remove the three bellhousing-to-pan bolts, one oil pan-to-bellhousing bolt, and the timing chain cover-to-oil pan fasteners. Move the power steering hose away from the oil pan by removing the bracket retaining nut, and then remove the air conditioning compressor without disconnecting the lines. Use a screwdriver to pry between the engine and transaxle until the bellhousing has moved away from the block to the limit of the loosened bolts. Unscrew the oil pan retaining bolts evenly until all are removed, then use a rubber mallet to loosen the oil pan seal and lower the oil pan, turning it as necessary to clear the exhaust system. Be cautious when prying between mating surfaces to avoid damage that could lead to leaks, and use a putty knife to cut through any sealant if necessary. For installation, thoroughly clean and degrease the mating surfaces of the lower engine block/crankcase and oil pan, removing all traces of sealant, and wipe out the oil pan. Apply a 1/8-inch wide bead of sealant to the oil pan flange, ensuring it is approximately 3/16-inch from the outside edge and around the inside edge of the bolt holes, as well as to the front flange where it meets the timing chain cover. The oil pan must be installed within 10 minutes of applying the sealant. Install the oil pan bolts, tightening them finger tight, followed by the timing chain cover-to-oil pan fasteners to the specified torque. Tighten the oil pan-to-engine block bolts in a circular pattern from the center outwards to the specified torque, then tighten the oil pan-to-bellhousing bolts and the transaxle to engine bolts evenly to the specified torque. Finally, lower the vehicle to the ground and wait at least 1 hour for the sealant to cure before refilling the engine with oil, trimming off any excess sealant with a sharp knife, and installing a new oil filter.