How to remove and install the hood cable and hood latch on the front of a Ford Taurus?

To replace the hood latch, first open the hood and mark a line around the latch for alignment, then remove the retaining bolts securing the latch to the radiator support and take out the latch. Next, squeeze the cable retainer to release the cable from the latch assembly and disengage the cable end plug from the latch. For the release cable, work in the engine compartment to disconnect it from the latch after removing the hood latch. On 2011 and earlier models, take out the radiator grille pin-type fasteners and panel, then detach the two release cable clips from the radiator support. For 2012 and later models, remove the battery tray and air filter housing. Loosen the left front wheel lug nuts, raise the vehicle securely on jackstands, and remove the wheel along with the inner fender splash shield. Open the two release cable clips in the upper part of the fender opening and detach the release cable from the clips. On 2012 and later models, it may be necessary to remove the Smart Junction Box, then disengage the release cable clip from the wiring harness. Remove the two hood release handle mounting bolts, pull out the handle, disengage the release cable from the release handle, and pull the release cable through the firewall. Finally, installation is the reverse of removal.

Genuine Ford Taurus Hood Cable

Hood Release Cable

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

5 Hood Cables found

View related parts
Ford Taurus Hood Control Cable Assembly
Part Number: AA5Z-16916-A
$68.32 MSRP: $105.63
You Save: $37.31 (36%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Cable Assy - Hood Control; Release Cable
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2010-2019 Ford Taurus | 4 Cyl 2.0L EcoBoost (240PS) , 6 Cyl 3.5L Cyclone Petrol TIVCT, 6 Cyl 3.5L DOHC T/C, 6 Cyl 3.5L DOHC VCT SMPI, 6 Cyl 3.7L DOHC | 6-Speed Automatic Transmission 6F Mid-Range, 6-Speed Automatic Transmission 6F50, 6-Speed Automatic Transmission 6F55, Four-Wheel Drive (Full Time) (Left Hand Drive), Four-Wheel Drive (Part Time) (Left Hand Drive), Front-Wheel Drive (Left Hand Drive), Left Hand Drive
View related parts
Ford Taurus Hood Control Cable Assembly
Part Number: YF1Z-16916-AA
$66.18 MSRP: $91.94
You Save: $25.76 (29%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Cable Assy - Hood Control; Release Cable
- Replaces: F6DZ-16916-AA
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 1996-2007 Ford Taurus | 6 Cyl 3.0L, 8 Cyl 3.4L | 4AT 4F50N, 4AT AX4N, 4AT AX4S
View related parts
Ford Taurus Hood Control Cable Assembly
Part Number: F6DZ-16916-AA
Product Specifications
- Other Name: Cable Assy - Hood Control
- Replaced by: YF1Z-16916-AA
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 1996-1999 Ford Taurus | 6 Cyl 3.0L, 8 Cyl 3.4L | 4AT AX4N, 4AT AX4S
View related parts
Ford Taurus Control Cable Assembly
Part Number: F2DZ-16916-A
Product Specifications
- Other Name: Cable Assy - Control; Release Cable
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 1992-1995 Ford Taurus | 6 Cyl 3.0L, 6 Cyl 3.2L, 6 Cyl 3.8L | 4AT AX4N, 4AT AX4S, 4AT AXOD-E, 5MT
View related parts
Ford Taurus Hood Control Cable Assembly
Part Number: 8G1Z-16916-A
Product Specifications
- Other Name: Cable Assy - Hood Control; Release Cable
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2008-2009 Ford Taurus | 6 Cyl 3.5L DOHC VCT SMPI | 6-Speed Automatic Transaxle - AWF21, 6-Speed Automatic Transmission 6F50, CVT Select Shift Transmission, Four-Wheel Drive (Part Time) (Left Hand Drive), Front-Wheel Drive (Left Hand Drive), Left Hand Drive

Ford Taurus Hood Cable

Ford Taurus Hood Cable provides drivers reliable hood popping and links the cabin release handle with the twin front latches. This way, service tasks can start quickly. For years, the Ford sedan has depended on this Hood Cable, a flexible steel core enclosed in protective housing, a basic pull system that transmits lever motion to the latch in one smooth stroke. There are two routing styles, a single run Hood Cable that splits near the grille and a dual run that uses a short primary line to a junction block with separate leads to each latch. But all keep every Taurus, and even older Taurus models, easy to service. After many years of exposure to moisture, the sheath can crack, allowing water to enter, which causes the latch to rust, fray, and go slack. An inspection will ensure that the Hood Cable doesn't stretch or snap on a Ford. If it snaps, the hood will be locked. Keeping your Hood Cable clean and lubricated helps to maintain the factory feel. Every Taurus driver should be able to access their engine components without hassle. This part is dependable Ford quality.

We provide a wide range of Ford Taurus Hood Cable at the optimal prices. If you need Ford Taurus Hood Cable, you can shop with confidence on our website. All our OEM parts come with a manufacturer's warranty and are delivered to your doorstep with a fast delivery service.

Ford Taurus Hood Cable Parts Questions & Experts Answers

Hood Control Cable Assembly
AA5Z-16916-A
Q: How to remove and install the hood cable and hood latch on the front of a Ford Taurus?
A:
To replace the hood latch, first open the hood and mark a line around the latch for alignment, then remove the retaining bolts securing the latch to the radiator support and take out the latch. Next, squeeze the cable retainer to release the cable from the latch assembly and disengage the cable end plug from the latch. For the release cable, work in the engine compartment to disconnect it from the latch after removing the hood latch. On 2011 and earlier models, take out the radiator grille pin-type fasteners and panel, then detach the two release cable clips from the radiator support. For 2012 and later models, remove the battery tray and air filter housing. Loosen the left front wheel lug nuts, raise the vehicle securely on jackstands, and remove the wheel along with the inner fender splash shield. Open the two release cable clips in the upper part of the fender opening and detach the release cable from the clips. On 2012 and later models, it may be necessary to remove the Smart Junction Box, then disengage the release cable clip from the wiring harness. Remove the two hood release handle mounting bolts, pull out the handle, disengage the release cable from the release handle, and pull the release cable through the firewall. Finally, installation is the reverse of removal.