How do you check and replace the shift cable and adjust it for proper operation on Ford Mustang?

Firmly apply the parking brake, depress the brake pedal, and try to momentarily operate the starter in each shift lever position; the starter should only operate when the manual shift lever is in PARK or NEUTRAL. If it operates in any other position, adjust the shift cable. If the starter still operates incorrectly after adjustment, the transmission range sensor may be defective. Always replace the shift lever cable retaining clip with a new one. Place the shift lever in NEUTRAL, raise the vehicle on jackstands, and remove the driveshaft. Secure the transmission with a jack, remove the transmission crossmember bolts, and partially lower the transmission to access the shift cable components. Pry the cable end off the transmission shift lever, and for 2010 and earlier models, remove the two shift cable bracket bolts to separate the shift cable and bracket from the transmission. For 2011 and later models, pry out the plastic cable mounting clip to separate the cable from the bracket. Disconnect the cable end from the shift lever by pushing the lock upward and removing the lock from the shift lever. Remove the clip and separate the shift cable from the bracket, then install in reverse order of removal, adjusting the cable afterward. When installing, attach the shift cable to the bracket with a new clip and adjust the cable end to the shift lever, ensuring the shift lever remains stationary. Slide the lock tab down to secure the shift cable end. In the passenger compartment, move the shifter into the 1st position and back into DRIVE. Raise the vehicle securely on jackstands, locate the cable adjuster, and release the adjuster mechanism. Rotate the shift lever on the transmission clockwise to its full travel and back three detents to the Drive position. Connect the shift cable to the shift lever and lock the adjuster. Remove the jackstands and lower the vehicle, verifying that the engine starts only in PARK and NEUTRAL, and that the back-up lights activate in REVERSE. Adjust the cable as necessary to meet these conditions, and it may also be necessary to adjust the transmission range sensor afterwards.

Genuine Ford Mustang Shift Cable

Transmission Shift Cable

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

16 Shift Cables found

View related parts
Ford Mustang Selector Lever Control Cable Assembly
Part Number: XR3Z-7E395-AA
$126.65 MSRP: $185.17
You Save: $58.52 (32%)
ADD TO CART
Product Specifications
- Other Name: Cable Assy - Selector Lever Control
- Manufacturer Note: #XR33-AA,AB, 4R70W
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 1999-2004 Ford Mustang | 6 Cyl 3.8L, 6 Cyl 3.8L OHV EFI, 6 Cyl 3.9L OHV EFI NA, 8 Cyl 4.6L, 8 Cyl 4.6L DOHC EFI, 8 Cyl 4.6L DOHC EFI S/C, 8 Cyl 4.6L SOHC EFI, 8 Cyl 5.4L | 4AT 4R70W, 4AT 4R75W, 4-Speed Automatic Transmission 4R70W (AODE), Left Hand Drive, Rear-Wheel Drive (Left Hand Drive)
View related parts
Ford Mustang Selector Lever Control Cable Assembly
Part Number: FR3Z-7E395-A
$89.91 MSRP: $131.45
You Save: $41.54 (32%)
ADD TO CART
Product Specifications
- Other Name: Cable Assembly - Selector Lever Control
- Replaced by: JR3Z-7E395-D
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2015-2017 Ford Mustang | 8 Cyl 5.0L MOD DOHC SEFI NA | 6-Speed Automatic Transmission (6R80), Left Hand Drive, Rear-Wheel Drive (Left Hand Drive)
View related parts
Ford Mustang Automatic Transmission Gear Shifter Control Cable
Part Number: 4R3Z-7E395-AA
$91.67 MSRP: $134.02
You Save: $42.35 (32%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Cable Assy - Selector Lever Control; Cable Assembly, Shift Control Cable
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2005-2010 Ford Mustang | 6 Cyl 4.0L SOHC EFI, 8 Cyl 4.6L SOHC EFI, 8 Cyl 5.4L DOHC EFI S/C ALUM, 8 Cyl 5.8L DOHC SC | 5-Speed Automatic Transmission 5R55S, Left Hand Drive, Rear-Wheel Drive (Left Hand Drive)
View related parts
Ford Mustang Automatic Transmission Shifter Cable
Part Number: FR3Z-7E395-B
$58.19 MSRP: $85.07
You Save: $26.88 (32%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Cable Assembly - Selector Lever Control; Shift Control Cable
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2015-2017 Ford Mustang | 4 Cyl 2.3L TIVCT DI TC, 6 Cyl 3.7L PFI NA | 6-Speed Automatic Transmission (6R80), Left Hand Drive, Rear-Wheel Drive (Left Hand Drive)
View related parts
Ford Mustang Selector Lever Control Cable Assembly
Part Number: BR3Z-7E395-C
$81.64 MSRP: $119.35
You Save: $37.71 (32%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Cable Assembly - Selector Lever Control; Cable Assembly, Shift Control Cable
- Replaces: BR3Z-7E395-A
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2011-2014 Ford Mustang | 8 Cyl 5.0L MOD DOHC SEFI NA | 6-Speed Automatic Transmission (6R80), Left Hand Drive, Rear-Wheel Drive (Left Hand Drive)
View related parts
Ford Mustang Selector Lever Control Cable Assembly
Part Number: BR3Z-7E395-A
$81.64 MSRP: $119.35
You Save: $37.71 (32%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Cable Assy - Selector Lever Control
- Replaced by: BR3Z-7E395-C
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2011-2012 Ford Mustang | 8 Cyl 5.0L MOD DOHC SEFI NA | 6-Speed Automatic Transmission (6R80), Left Hand Drive, Rear-Wheel Drive (Left Hand Drive)
View related parts
Ford Mustang Selector Lever Control Cable Assembly
Part Number: BR3Z-7E395-B
$81.38 MSRP: $118.98
You Save: $37.60 (32%)
ADD TO CART
Product Specifications
- Other Name: Cable Assy - Selector Lever Control
- Replaced by: BR3Z-7E395-D
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2011-2012 Ford Mustang | 6 Cyl 3.7L PFI NA | 6-Speed Automatic Transmission (6R80), Left Hand Drive, Rear-Wheel Drive (Left Hand Drive)
View related parts
Ford Mustang Selector Lever Con Cable Assembly
Part Number: JR3Z-7E395-D
$89.91 MSRP: $131.45
You Save: $41.54 (32%)
ADD TO CART
Product Specifications
- Other Name: Cable Assembly - Selector Lever Con; Cable, Shift Control Cable
- Replaces: JR3Z-7E395-A, FR3Z-7E395-A
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2015-2023 Ford Mustang | 8 Cyl 5.0 L GAS, 8 Cyl 5.0L MOD DOHC SEFI NA | 10-Speed Automatic Transmission (10R80), 6-Speed Automatic Transmission (6R80), Left Hand Drive, Rear-Wheel Drive (Left Hand Drive)
View related parts
Ford Mustang Selector Lever Con Cable Assembly
Part Number: JR3Z-7E395-C
$84.39 MSRP: $123.38
You Save: $38.99 (32%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Cable Assembly - Selector Lever Con; Cable, Shift Control Cable
- Replaces: JR3Z-7E395-B
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2018-2023 Ford Mustang | 4 Cyl 2.3 L GAS, 4 Cyl 2.3L TIVCT DI TC | 10-Speed Automatic Transmission (10R80), Left Hand Drive, Rear-Wheel Drive (Left Hand Drive)
View related parts
Ford Mustang Selector Lever Control Cable Assembly
Part Number: JR3Z-7E395-A
$89.91 MSRP: $131.45
You Save: $41.54 (32%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Cable Assembly - Selector Lever Control
- Replaced by: JR3Z-7E395-D
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2018-2019 Ford Mustang | 8 Cyl 5.0L MOD DOHC SEFI NA | 10-Speed Automatic Transmission (10R80), Left Hand Drive, Rear-Wheel Drive (Left Hand Drive)
View related parts
Ford Mustang CABLE ASY - SELECTOR LEVER CON
Part Number: KR3Z-7D246-A
$123.39 MSRP: $180.40
You Save: $57.01 (32%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Cable Assembly, Shift Control Cable
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2020-2022 Ford Mustang | 8 Cyl 5.2 L GAS
View related parts
Ford Mustang Shift Control Cable
Part Number: JR3Z-7E395-B
$84.39 MSRP: $123.38
You Save: $38.99 (32%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Cable Assembly - Selector Lever Control
- Replaced by: JR3Z-7E395-C
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2018-2019 Ford Mustang | 4 Cyl 2.3L TIVCT DI TC | 10-Speed Automatic Transmission (10R80), Left Hand Drive, Rear-Wheel Drive (Left Hand Drive)
View related parts
Ford Mustang CABLE ASY - SELECTOR LEVER CON
Part Number: PR3Z-7E395-A
$100.32 MSRP: $146.67
You Save: $46.35 (32%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Cable
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2024 Ford Mustang | 8 Cyl 5.0 L GAS
View related parts
Ford Mustang CABLE ASY - SELECTOR LEVER CON
Part Number: PR3Z-7E395-B
$101.20 MSRP: $147.95
You Save: $46.75 (32%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Cable
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2024 Ford Mustang | 4 Cyl 2.3 L GAS
View related parts
Ford Mustang Shift Control Cable
Part Number: BR3Z-7E395-D
$81.38 MSRP: $118.98
You Save: $37.60 (32%)
ADD TO CART
Product Specifications
- Other Name: Cable Assembly - Selector Lever Control; Cable Assembly
- Replaces: BR3Z-7E395-B
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2011-2014 Ford Mustang | 6 Cyl 3.7L PFI NA | 6-Speed Automatic Transmission (6R80), Left Hand Drive, Rear-Wheel Drive (Left Hand Drive)
View related parts
Ford Mustang Selector Lever Control Cable Assembly
Part Number: F4ZZ-7E395-A
Product Specifications
- Other Name: Cable Assy - Selector Lever Control
- Manufacturer Note: #F4ZC-BC, AOD-E/4R70W
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 1996-1998 Ford Mustang | 6 Cyl 3.8L, 8 Cyl 4.6L | 4AT 4R70W

Ford Mustang Shift Cable

We provide a wide range of Ford Mustang Shift Cable at the best prices possible. If you need Ford Mustang Shift Cable, you can shop with confidence on our website. All our OEM parts come with a manufacturer's warranty and are delivered to your door step with a fast delivery service.

Ford Mustang Shift Cable Parts Questions & Experts Answers

Automatic Transmission Gear Shifter Control Cable
4R3Z-7E395-AA
Q: How do you check and replace the shift cable and adjust it for proper operation on Ford Mustang?
A:
Firmly apply the parking brake, depress the brake pedal, and try to momentarily operate the starter in each shift lever position; the starter should only operate when the manual shift lever is in PARK or NEUTRAL. If it operates in any other position, adjust the shift cable. If the starter still operates incorrectly after adjustment, the transmission range sensor may be defective. Always replace the shift lever cable retaining clip with a new one. Place the shift lever in NEUTRAL, raise the vehicle on jackstands, and remove the driveshaft. Secure the transmission with a jack, remove the transmission crossmember bolts, and partially lower the transmission to access the shift cable components. Pry the cable end off the transmission shift lever, and for 2010 and earlier models, remove the two shift cable bracket bolts to separate the shift cable and bracket from the transmission. For 2011 and later models, pry out the plastic cable mounting clip to separate the cable from the bracket. Disconnect the cable end from the shift lever by pushing the lock upward and removing the lock from the shift lever. Remove the clip and separate the shift cable from the bracket, then install in reverse order of removal, adjusting the cable afterward. When installing, attach the shift cable to the bracket with a new clip and adjust the cable end to the shift lever, ensuring the shift lever remains stationary. Slide the lock tab down to secure the shift cable end. In the passenger compartment, move the shifter into the 1st position and back into DRIVE. Raise the vehicle securely on jackstands, locate the cable adjuster, and release the adjuster mechanism. Rotate the shift lever on the transmission clockwise to its full travel and back three detents to the Drive position. Connect the shift cable to the shift lever and lock the adjuster. Remove the jackstands and lower the vehicle, verifying that the engine starts only in PARK and NEUTRAL, and that the back-up lights activate in REVERSE. Adjust the cable as necessary to meet these conditions, and it may also be necessary to adjust the transmission range sensor afterwards.