How to replace the fuel rail pressure sensor on turbocharged car?

To relieve the fuel pressure, disconnect the cable from the negative battery terminal. For 2.0L models, remove the charge air cooler inlet and middle tubes, followed by the drive belt and alternator. For all models, disconnect the FRP sensor electrical connector and unscrew and remove the FRP sensor from the fuel rail. When installing, lubricate the O-ring with engine oil and tighten the sensor.

How to replace the fuel tank pressure sensor?

The FTP sensor is used to monitor the fuel tank pressure or vacuum during the 080-11 test portion for emissions integrity. This test scans various sensors and output actuators to detect abnormal amounts of fuel vapors that may not be purging into the canister or the intake system for recycling. The FTP sensor helps the PCM monitor this pressure differential (pressure vs vacuum) inside the fuel tank. A problem in the fuel tank pressure sensor circuit will set a diagnostic trouble code. The Fuel Tank Pressure (FTP) sensor is part of the vapor tube assembly and serviced as one unit. To replace the FTP sensor, raise the vehicle and support it securely on jackstands. Disconnect the vapor tube from the quick disconnect fittings and remove the vapor tube and FTP sensor. Installation is the reverse of removal.

How to relieve fuel pressure and install a FPS sensor?

To relieve the fuel pressure, disconnect the cable from the negative battery terminal. Lift the engine cover up and off of the ballstuds, then remove the cover. Disconnect the FPS sensor electrical connector. Unscrew and remove the sensor from the supply line. For installation, lubricate the O-ring with engine oil and tighten the sensor.

Genuine Ford Fusion Fuel Pressure Sensor

Fuel Tank Pressure Sensor

Enter your vehicle info to find more parts and verify fitment

Select Vehicle by VIN
Select Vehicle by Model

Select by VIN

Enter your VIN for the most accurate results.

Select by Model

-- Select Make --

-- Select Model --

-- Select Year --

7 Fuel Pressure Sensors found

View related parts
Ford Fusion Fuel Injector Pressure Sensor
Part Number: BU5Z-9F972-B
- Other Name: Sensor - Fuel Injector Pressure; Pressure Sensor, Sensor
- Replaces: CM-5226, BU5Z-9F972-A
$60.83 MSRP: $100.55
You Save: $39.72 (40%)

Add to Cart
More Info
Fits the following Vehicles:
2013-2019 Ford Fusion | 4 Cyl 1.5L GTDI, 4 Cyl 1.6L PI TC ETHNL, 4 Cyl 2.0L EcoBoost (200PS), 4 Cyl 2.0L EcoBoost (240PS), 6 Cyl 2.7L | 6-Speed Automatic Transmission 6F Mid-Range, 6-Speed Automatic Transmission 6F55, 6-Speed Manual Transmission - B6, ECVT Auto Trans Power Split, Four-Wheel Drive (Full Time) (Left Hand Drive), Front-Wheel Drive (Left Hand Drive), Left Hand Drive
Less Info
View related parts
Ford Fusion Fuel Injector Pressure Sensor
Part Number: 3F2Z-9G756-AC
- Other Name: Sensor - Fuel Injector Pressure; Damper, Pressure Sensor
- Manufacturer Note: Also serviced in 9F792. Mounting screws W705870-S437, 6.8L
$96.47 MSRP: $159.45
You Save: $62.98 (40%)

Add to Cart
More Info
Fits the following Vehicles:
2006-2009 Ford Fusion | 4 Cyl 2.3L | 5-Speed Manual Transmission (G5M), Four-Wheel Drive (Full Time) (Left Hand Drive), Front-Wheel Drive (Left Hand Drive), Left Hand Drive
Less Info
View related parts
Ford Fusion Fuel Injector Pressure Sensor
Part Number: BM5Z-9F972-A
- Other Name: Sensor - Fuel Injector Pressure; Pressure Sensor
$69.85 MSRP: $115.45
You Save: $45.60 (40%)

Add to Cart
More Info
Fits the following Vehicles:
2013-2016 Ford Fusion | 4 Cyl 1.6L PI TC ETHNL, 4 Cyl 2.0L EcoBoost (240PS) | 6-Speed Automatic Transmission 6F Mid-Range, 6-Speed Automatic Transmission 6F55, 6-Speed Manual Transmission - B6, ECVT Auto Trans Power Split, Four-Wheel Drive (Full Time) (Left Hand Drive), Front-Wheel Drive (Left Hand Drive), Left Hand Drive
Less Info
View related parts
Ford Fusion Fuel Injector Pressure Sensor
Part Number: EJ7Z-9F972-A
- Other Name: Sensor - Fuel Injector Pressure; Pressure Sensor
$60.29 MSRP: $119.82
You Save: $59.53 (50%)

Add to Cart
More Info
Fits the following Vehicles:
2017-2019 Ford Fusion | 4 Cyl 2.0L EcoBoost (200PS), 4 Cyl 2.0L EcoBoost (240PS) | 6-Speed Automatic Transmission 6F Mid-Range, 6-Speed Automatic Transmission 6F55, 6-Speed Manual Transmission - B6, ECVT Auto Trans Power Split, Four-Wheel Drive (Full Time) (Left Hand Drive), Front-Wheel Drive (Left Hand Drive), Left Hand Drive
Less Info
View related parts
Ford Fusion Fuel Injector Pressure Sensor
Part Number: BU5Z-9F972-A
- Other Name: Sensor - Fuel Injector Pressure
- Replaced by: BU5Z-9F972-B
$60.83 MSRP: $100.55
You Save: $39.72 (40%)

Add to Cart
More Info
Fits the following Vehicles:
2013-2016 Ford Fusion | 4 Cyl 1.5L GTDI, 4 Cyl 1.6L PI TC ETHNL, 4 Cyl 2.0L EcoBoost (240PS) | 6-Speed Automatic Transmission 6F Mid-Range, 6-Speed Automatic Transmission 6F55, 6-Speed Manual Transmission - B6, ECVT Auto Trans Power Split, Four-Wheel Drive (Full Time) (Left Hand Drive), Front-Wheel Drive (Left Hand Drive), Left Hand Drive
Less Info
View related parts
Ford Fusion Fuel Injector Pressure Sensor
Part Number: DS7Z-9F972-A
- Other Name: Sensor - Fuel Injector Pressure
- Replaced by: DS7Z-9F972-CA
$58.63 MSRP: $96.91
You Save: $38.28 (40%)

Add to Cart
More Info
Fits the following Vehicles:
2014-2019 Ford Fusion | 4 Cyl 1.5L GTDI | 6-Speed Automatic Transmission 6F Mid-Range, 6-Speed Automatic Transmission 6F55, 6-Speed Manual Transmission - B6, ECVT Auto Trans Power Split, Four-Wheel Drive (Full Time) (Left Hand Drive), Front-Wheel Drive (Left Hand Drive), Left Hand Drive
Less Info
View related parts
Ford Fusion Sensor Assembly
Part Number: DU5Z-9C052-A
- Other Name: Sensor Assy; Pressure Sensor, Transducer
$67.43 MSRP: $111.45
You Save: $44.02 (40%)

Add to Cart
More Info
Fits the following Vehicles:
2013-2016 Ford Fusion | 4 Cyl 2.0L Duratec Hybrid (130kW) | 6-Speed Automatic Transmission 6F Mid-Range, 6-Speed Automatic Transmission 6F55, 6-Speed Manual Transmission - B6, ECVT Auto Trans Power Split, Four-Wheel Drive (Full Time) (Left Hand Drive), Front-Wheel Drive (Left Hand Drive), Left Hand Drive
Less Info

Ford Fusion Fuel Pressure Sensor Parts Questions & Answers

Fuel Injector Pressure Sensor
BM5Z-9F972-A
Q: How to replace the fuel rail pressure sensor on turbocharged car?
A: To relieve the fuel pressure, disconnect the cable from the negative battery terminal. For 2.0L models, remove the charge air cooler inlet and middle tubes, followed by the drive belt and alternator. For all models, disconnect the FRP sensor electrical connector and unscrew and remove the FRP sensor from the fuel rail. When installing, lubricate the O-ring with engine oil and tighten the sensor.
Fuel Injector Pressure Sensor
BU5Z-9F972-A
Q: How to replace the fuel tank pressure sensor?
A: The FTP sensor is used to monitor the fuel tank pressure or vacuum during the 080-11 test portion for emissions integrity. This test scans various sensors and output actuators to detect abnormal amounts of fuel vapors that may not be purging into the canister or the intake system for recycling. The FTP sensor helps the PCM monitor this pressure differential (pressure vs vacuum) inside the fuel tank. A problem in the fuel tank pressure sensor circuit will set a diagnostic trouble code. The Fuel Tank Pressure (FTP) sensor is part of the vapor tube assembly and serviced as one unit. To replace the FTP sensor, raise the vehicle and support it securely on jackstands. Disconnect the vapor tube from the quick disconnect fittings and remove the vapor tube and FTP sensor. Installation is the reverse of removal.
Fuel Injector Pressure Sensor
3F2Z-9G756-AC
Q: How to relieve fuel pressure and install a FPS sensor?
A: To relieve the fuel pressure, disconnect the cable from the negative battery terminal. Lift the engine cover up and off of the ballstuds, then remove the cover. Disconnect the FPS sensor electrical connector. Unscrew and remove the sensor from the supply line. For installation, lubricate the O-ring with engine oil and tighten the sensor.