Ford 6U5Z-18808-BA Speaker Assembly

For 2007 and earlier models, disconnect the negative battery cable. Remove the radio by using special tools or bent coat hanger wire. Insert the tools into the holes at the corners of the radio assembly to release the retaining clips and pull out the radio. Disconnect the antenna and electrical connector, then remove the radio. Reinstall in reverse, ensuring the retaining clip snaps into place. After reconnecting the battery, the PCM needs to relearn its idle and fuel trim strategy. For 2008 and later models, remove the center middle instrument panel trim panel. Remove the audio unit mounting screws and separate the unit from the trim panel. Disconnect the antenna and other wiring if there's a navigation system. Side brackets can be removed if needed. Reinstall in reverse. Note that a new radio must be programmed by a dealer service department. For speakers, remove the door trim panel and speaker mounting screws for front door speakers. Remove the door trim panel for rear door speakers. Access the rear subwoofer speaker by removing various trim panels. Disconnect the wiring, remove the mounting bolts, and take out the speaker assembly. Installation follows the reverse order.

Pull off the cable that is connected at the negative terminal of the battery. Pull back the Instrument panel center bezel. Take out the radio mounting screws and thus releases the radio from the instrument panel, just pull it out merely to allow access to the electrical connectors, and the antenna cable lies at the back of the radio unit. The electrical connectors and the antenna lead must be disconnected from the backside of the radio and the radio taken out. Installation is the process opposite to the removal and is similarly carried out to assemble a device on a surface it is to operate on. For front door speakers, first, you have to take out the front door trim panel and next, you have to remove the mounting screws of the speaker. To accomplish it, reach for the pin, disconnect the electrical connector from the speaker, and then take the speaker out. Removal and Installation refers to responding accordingly; it means that installation is the antonym of removal. The front door speaker trim panel and the speaker mounting screws must be detached for this part. To remove the speaker, pull out on the speaker, then unlock the electrical connector by pressing on the tab located at the top of the connector and take off the speaker. Removal on the other hand is the reverse of installation. For rear door speakers, pull the rear door trim panel, then there will be screws that will have to be removed for the speakers. Slide out the speaker, unscrew the electrical connection and take out the speaker. Removal is the exact opposite of installation. For the instrument panel speaker, on 2009 and later models, pull the mat at the upper storage compartment outwards, then two screws will be revealed, by raising the upper storage compartment slightly, those two screws are detached so as to release the electrical connector of the speaker. Detach the top most portion of the storage area and in some instances, you shall have to unscrew the speaker mounting locations before lifting the speaker. Installation is the process of putting back something that has been earlier removed.

The models are fitted with speakers in the doors from the factory and extra rear speakers are provided for models with AM/FM sound. Your specific model may have variations from the following procedure due to size and configuration of aftermarket speakers which has been fitted into some variants. To take out the door speakers, first, one has to take off the door panel, then the speakers that are attached to the door using screws are pulled out and the electrical connection also is disconnected. There are some conditions in which it is prohibited to continue the operation of radio with the speakers disconnected. Installation, on the other hand, is done in the reverse order that removal took. The procedure for the rear speakers is similar to that of the front ones: you have to take out the screws, extract the speaker out of the trim panel and, finally, unlock the electrical connector. As before, do not operate the radio with the speakers disconnected, and installation is done in the reverse order to the removal.

Speakers in doors are fitted before they are shipped from the factory and extra rear speakers are fitted in models equipped with AM/FM sound systems. Your particular model might deviate from the following process because of the configuration of various popular kinds of speakers used in certain versions of SH cars. They include; SPEAKER: Audio of door speakers can only be accessed after you have stripped the door trim panel and also after the removal of the screws that was used to fix the speaker to the door. Take out the speaker and unplug the electrical connection from it, do not use the radio with the speakers removed. Installation is done in the opposite to the removal procedures enumerated above. To decommission the rear speakers, one will have to unscrew the speaker and pull it out from the trim panel then disconnect the electrical connection with the speakers disconnected, do not operate the radio. It is also done in reverse to the removal process that has been explained above.

For 2007 and earlier models, disconnect the negative battery cable. Remove the radio by using special tools or bent coat hanger wire. Insert the tools into the holes at the corners of the radio assembly to release the retaining clips and pull out the radio. Disconnect the antenna and electrical connector, then remove the radio. Reinstall in reverse, ensuring the retaining clip snaps into place. After reconnecting the battery, the PCM needs to relearn its idle and fuel trim strategy. For 2008 and later models, remove the center middle instrument panel trim panel. Remove the audio unit mounting screws and separate the unit from the trim panel. Disconnect the antenna and other wiring if there's a navigation system. Side brackets can be removed if needed. Reinstall in reverse. Note that a new radio must be programmed by a dealer service department. For speakers, remove the door trim panel and speaker mounting screws for front door speakers. Remove the door trim panel for rear door speakers. Access the rear subwoofer speaker by removing various trim panels. Disconnect the wiring, remove the mounting bolts, and take out the speaker assembly. Installation follows the reverse order.

Pull the C-pillar trim panel inward to release it.