How do I replace and inspect brake discs on a Ford Taurus?

Begin by loosening the wheel lug nuts, raising the vehicle and supporting it securely on jackstands. Remove the brake caliper; it isn't necessary to disconnect the brake hose. After removing the caliper bolts, suspend the caliper out of the way with a piece of wire. Visually inspect the disc surface for score marks and other damage. Light scratches and shallow grooves are normal after use but deep scoring requires disc removal and refinishing by an automotive machine shop. Check both sides of the disc.To check disc runout, place a dial indicator at a point about 1/2-inch from the outer edge of the disc. Set the indicator to zero and turn the disc. The indicator reading should not exceed the specified allowable runout limit. If it does, the disc should be refinished by an automotive machine shop. It's recommended to have the discs resurfaced regardless of the dial indicator reading, to impart a smooth finish and ensure a perfectly flat surface. At the very least, remove the glaze from the surface with emery cloth or sandpaper, using a swirling motion.It's absolutely critical that the disc not be machined to a thickness under the specified minimum thickness. The minimum thickness is cast or stamped into the inside of the disc. The disc thickness can be checked with a micrometer. To remove the disc, discard the caliper mounting bracket bolts and remove the bracket. The caliper mounting bracket bolts are one-time use, so always use new ones when installing the caliper. Remove and discard the disc retaining screw and remove the disc.For installation, while the disc is off, wire-brush the backside of the center portion that contacts the wheel hub and clean off any rust or dirt on the hub face. Apply small dots of high-temperature anti-seize around the circumference of the hub, and around the raised center portion. Place the disc in position over the threaded studs, install a new disc retaining screw and tighten to the correct torque. Install the caliper mounting bracket and caliper; use new bolts and tighten them to the correct torque. Install the wheel, then lower the vehicle to the ground. Tighten the lug nuts to the correct torque. Depress the brake pedal a few times to bring the brake pads into contact with the disc. Bleeding won't be necessary unless the brake hose was disconnected from the caliper. Check the operation of the brakes carefully before driving the vehicle. If new or resurfaced rear discs are being installed, check the operation of the parking brake.

Genuine Ford Taurus Brake Disc

Disc Rotor

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

34 Brake Discs found

View related parts
Ford Taurus Rotor Assembly - Brake
Part Number: DG1Z-2C026-A
$70.06 MSRP: $108.32
You Save: $38.26 (36%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Disc - Brake; Rotor
- Position: Passenger Side/Driver Side
- Replaced by: EU2Z-2V026-B
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2013-2019 Ford Taurus | 4 Cyl 2.0L EcoBoost (240PS) , 6 Cyl 3.5L Cyclone Petrol TIVCT, 6 Cyl 3.5L DOHC T/C, 6 Cyl 3.7L DOHC | 6-Speed Automatic Transmission 6F Mid-Range, 6-Speed Automatic Transmission 6F50, 6-Speed Automatic Transmission 6F55, Four-Wheel Drive (Full Time) (Left Hand Drive), Four-Wheel Drive (Part Time) (Left Hand Drive), Front-Wheel Drive (Left Hand Drive), Left Hand Drive
View related parts
Ford Taurus Rotor Assembly - Brake
Part Number: GG1Z-1125-A
$71.49 MSRP: $108.32
You Save: $36.83 (34%)
ADD TO CART
Product Specifications
- Other Name: Disc - Brake; Rotor
- Position: Passenger Side/Driver Side
- Replaced by: EU2Z-1V125-B
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2016-2019 Ford Taurus | 4 Cyl 2.0L EcoBoost (240PS) , 6 Cyl 3.5L Cyclone Petrol TIVCT, 6 Cyl 3.5L DOHC T/C, 6 Cyl 3.7L DOHC | 6-Speed Automatic Transmission 6F Mid-Range, 6-Speed Automatic Transmission 6F50, 6-Speed Automatic Transmission 6F55, Four-Wheel Drive (Full Time) (Left Hand Drive), Four-Wheel Drive (Part Time) (Left Hand Drive), Front-Wheel Drive (Left Hand Drive), Left Hand Drive
View related parts
Ford Taurus Hub And Disc Assembly
Part Number: 9U2Z-1V125-B
$70.06 MSRP: $108.32
You Save: $38.26 (36%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Hub And Disc Assy
- Manufacturer Note: Ford Retail Spec
- Replaced by: 9U2Z-1V125-C
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2010-2012 Ford Taurus | 6 Cyl 3.5L DOHC T/C, 6 Cyl 3.5L DOHC VCT SMPI | 6-Speed Automatic Transmission 6F Mid-Range, 6-Speed Automatic Transmission 6F50, 6-Speed Automatic Transmission 6F55, Four-Wheel Drive (Full Time) (Left Hand Drive), Four-Wheel Drive (Part Time) (Left Hand Drive), Front-Wheel Drive (Left Hand Drive), Left Hand Drive
View related parts
Ford Taurus Rotor Assembly
Part Number: CB5Z-1125-A
$95.26 MSRP: $144.33
You Save: $49.07 (34%)
Ships in 1 Business Day
ADD TO CART
Product Specifications
- Other Name: Rotor Assy; Rotor
- Position: Passenger Side/Driver Side
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2011-2019 Ford Taurus | 4 Cyl 2.0L EcoBoost (240PS) , 6 Cyl 3.5L Cyclone Petrol TIVCT, 6 Cyl 3.5L DOHC T/C, 6 Cyl 3.5L DOHC VCT SMPI, 6 Cyl 3.7L DOHC | 6-Speed Automatic Transmission 6F Mid-Range, 6-Speed Automatic Transmission 6F50, 6-Speed Automatic Transmission 6F55, Four-Wheel Drive (Full Time) (Left Hand Drive), Four-Wheel Drive (Part Time) (Left Hand Drive), Front-Wheel Drive (Left Hand Drive), Left Hand Drive
View related parts
Ford Taurus Rotor Assembly - Brake
Part Number: EU2Z-2V026-A
$71.49 MSRP: $108.32
You Save: $36.83 (34%)
Ships in 1 Business Day
ADD TO CART
Product Specifications
- Other Name: Disc - Brake; Rotor
- Position: Passenger Side/Driver Side
- Replaced by: EU2Z-2V026-B
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2013-2019 Ford Taurus | 4 Cyl 2.0L EcoBoost (240PS) , 6 Cyl 3.5L Cyclone Petrol TIVCT, 6 Cyl 3.5L DOHC T/C, 6 Cyl 3.7L DOHC | 6-Speed Automatic Transmission 6F Mid-Range, 6-Speed Automatic Transmission 6F50, 6-Speed Automatic Transmission 6F55, Four-Wheel Drive (Full Time) (Left Hand Drive), Four-Wheel Drive (Part Time) (Left Hand Drive), Front-Wheel Drive (Left Hand Drive), Left Hand Drive
View related parts
Ford Taurus Rotor Assembly
Part Number: DG1Z-1125-C
$71.49 MSRP: $108.32
You Save: $36.83 (34%)
Ships in 1 Business Day
ADD TO CART
Product Specifications
- Other Name: Rotor Assy
- Replaced by: EU2Z-1V125-B
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2013-2016 Ford Taurus | 4 Cyl 2.0L EcoBoost (240PS) , 6 Cyl 3.5L Cyclone Petrol TIVCT, 6 Cyl 3.5L DOHC T/C, 6 Cyl 3.7L DOHC | 6-Speed Automatic Transmission 6F Mid-Range, 6-Speed Automatic Transmission 6F50, 6-Speed Automatic Transmission 6F55, Four-Wheel Drive (Full Time) (Left Hand Drive), Four-Wheel Drive (Part Time) (Left Hand Drive), Front-Wheel Drive (Left Hand Drive), Left Hand Drive
View related parts
Ford Taurus Rotor Assembly
Part Number: DG1Z-1125-B
$71.49 MSRP: $108.32
You Save: $36.83 (34%)
Ships in 1 Business Day
ADD TO CART
Product Specifications
- Other Name: Rotor Assy
- Position: Passenger Side/Driver Side
- Replaced by: EU2Z-1V125-B
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2013 Ford Taurus | 4 Cyl 2.0L EcoBoost (240PS) , 6 Cyl 3.5L Cyclone Petrol TIVCT, 6 Cyl 3.5L DOHC T/C, 6 Cyl 3.7L DOHC | 6-Speed Automatic Transmission 6F Mid-Range, 6-Speed Automatic Transmission 6F50, 6-Speed Automatic Transmission 6F55, Four-Wheel Drive (Full Time) (Left Hand Drive), Four-Wheel Drive (Part Time) (Left Hand Drive), Front-Wheel Drive (Left Hand Drive), Left Hand Drive
View related parts
Ford Taurus Rotor Assembly
Part Number: 4F1Z-1125-AA
$70.06 MSRP: $108.32
You Save: $38.26 (36%)
ADD TO CART
Product Specifications
- Other Name: Rotor Assy
- Replaced by: YF1Z-1V125-G
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2004-2007 Ford Taurus | 6 Cyl 3.0L | 4AT 4F50N
View related parts
Ford Taurus Rotor Assembly - Brake
Part Number: 8G1Z-2C026-B
$71.49 MSRP: $108.32
You Save: $36.83 (34%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Disc - Brake
- Manufacturer Note: Warranty Eligible
- Replaced by: 5U2Z-1V125-GD
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2008-2011 Ford Taurus | 6 Cyl 3.5L DOHC T/C, 6 Cyl 3.5L DOHC VCT SMPI | 6-Speed Automatic Transaxle - AWF21, 6-Speed Automatic Transmission 6F Mid-Range, 6-Speed Automatic Transmission 6F50, 6-Speed Automatic Transmission 6F55, CVT Select Shift Transmission, Four-Wheel Drive (Full Time) (Left Hand Drive), Four-Wheel Drive (Part Time) (Left Hand Drive), Front-Wheel Drive (Left Hand Drive), Left Hand Drive
View related parts
Ford Taurus Rotor Assembly - Brake
Part Number: G2MZ-2V026-GA
$70.06 MSRP: $108.32
You Save: $38.26 (36%)
ADD TO CART
Product Specifications
- Other Name: ROTOR ASY - BRAKE
- Manufacturer Note: High Level Aftermarket Spec / Non Warranty Repairs
- Replaced by: EU2Z-2V026-B
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2013-2019 Ford Taurus | 4 Cyl 2.0L EcoBoost (240PS) , 6 Cyl 3.5L Cyclone Petrol TIVCT, 6 Cyl 3.5L DOHC T/C, 6 Cyl 3.7L DOHC | 6-Speed Automatic Transmission 6F Mid-Range, 6-Speed Automatic Transmission 6F50, 6-Speed Automatic Transmission 6F55, Four-Wheel Drive (Full Time) (Left Hand Drive), Four-Wheel Drive (Part Time) (Left Hand Drive), Front-Wheel Drive (Left Hand Drive), Left Hand Drive
View related parts
Ford Taurus Rotor Assembly
Part Number: FODZ-2C026-A
$36.59 MSRP: $49.99
You Save: $13.40 (27%)
ADD TO CART
Product Specifications
- Other Name: ROTOR ASY
- Replaced by: YF1Z-1V125-AA
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 1990-1992 Ford Taurus | 4 Cyl 2.5L, 6 Cyl 3.0L, 6 Cyl 3.8L | 4AT AX4S, 4AT AXOD, 4AT AXOD-E, 5MT
View related parts
Ford Taurus Disc - Brake
Part Number: YF1Z-2C026-BA
$36.59 MSRP: $49.99
You Save: $13.40 (27%)
ADD TO CART
Product Specifications
- Replaced by: YF1Z-1V125-DB
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2000-2007 Ford Taurus | 6 Cyl 3.0L | 4AT 4F50N, 4AT AX4N, 4AT AX4S
View related parts
Ford Taurus Rotor Assembly
Part Number: 8G1Z-1125-B
$82.49 MSRP: $124.98
You Save: $42.49 (34%)
Ships in 1 Business Day
ADD TO CART
Product Specifications
- Other Name: Rotor Assy; Rotor
- Manufacturer Note: Warranty Eligible
- Replaces: 8G1Z-1125-A, 5F9Z-1125-C
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2008-2009 Ford Taurus | 6 Cyl 3.5L DOHC VCT SMPI | 6-Speed Automatic Transaxle - AWF21, 6-Speed Automatic Transmission 6F50, CVT Select Shift Transmission, Four-Wheel Drive (Part Time) (Left Hand Drive), Front-Wheel Drive (Left Hand Drive), Left Hand Drive
View related parts
Ford Taurus Rotor Assembly
Part Number: 5U2Z-1V125-GC
$71.49 MSRP: $108.32
You Save: $36.83 (34%)
Ships in 1 Business Day
ADD TO CART
Product Specifications
- Other Name: Rotor Assy
- Manufacturer Note: Ford Retail Spec
- Replaced by: 5U2Z-1V125-GD
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2010-2012 Ford Taurus | 6 Cyl 3.5L DOHC T/C, 6 Cyl 3.5L DOHC VCT SMPI | 6-Speed Automatic Transmission 6F Mid-Range, 6-Speed Automatic Transmission 6F50, 6-Speed Automatic Transmission 6F55, Four-Wheel Drive (Full Time) (Left Hand Drive), Four-Wheel Drive (Part Time) (Left Hand Drive), Front-Wheel Drive (Left Hand Drive), Left Hand Drive
View related parts
Ford Taurus Rotor Assembly
Part Number: 8G1Z-1125-A
$82.49 MSRP: $124.98
You Save: $42.49 (34%)
Ships in 1 Business Day
ADD TO CART
Product Specifications
- Other Name: Rotor Assy
- Manufacturer Note: Warranty Eligible
- Replaced by: 8G1Z-1125-B
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2008 Ford Taurus | 6 Cyl 3.5L DOHC VCT SMPI | 6-Speed Automatic Transaxle - AWF21, 6-Speed Automatic Transmission 6F50, CVT Select Shift Transmission, Four-Wheel Drive (Part Time) (Left Hand Drive), Front-Wheel Drive (Left Hand Drive), Left Hand Drive
View related parts
Ford Taurus Rotor Assembly - Brake
Part Number: 8G1Z-2C026-A
$71.49 MSRP: $108.32
You Save: $36.83 (34%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Disc - Brake
- Manufacturer Note: Warranty Eligible
- Replaced by: 5U2Z-1V125-GD
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2008 Ford Taurus | 6 Cyl 3.5L DOHC VCT SMPI | 6-Speed Automatic Transaxle - AWF21, 6-Speed Automatic Transmission 6F50, CVT Select Shift Transmission, Four-Wheel Drive (Part Time) (Left Hand Drive), Front-Wheel Drive (Left Hand Drive), Left Hand Drive
View related parts
Ford Taurus Rotor Assembly
Part Number: 5U2Z-1V125-R
$70.06 MSRP: $108.32
You Save: $38.26 (36%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Rotor Assy
- Manufacturer Note: Ford Retail Spec
- Replaced by: 5U2Z-1V125-MG
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2008-2009 Ford Taurus | 6 Cyl 3.5L DOHC VCT SMPI | 6-Speed Automatic Transaxle - AWF21, 6-Speed Automatic Transmission 6F50, CVT Select Shift Transmission, Four-Wheel Drive (Part Time) (Left Hand Drive), Front-Wheel Drive (Left Hand Drive), Left Hand Drive
View related parts
Ford Taurus Rotor Assembly
Part Number: F4DZ-1125-A
$36.59 MSRP: $49.99
You Save: $13.40 (27%)
ADD TO CART
Product Specifications
- Other Name: ROTOR ASY
- Replaced by: YF1Z-1V125-C
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 1994-1995 Ford Taurus | 6 Cyl 3.0L, 6 Cyl 3.2L, 6 Cyl 3.8L | 4AT AX4N, 4AT AX4S, 4AT AXOD-E, 5MT
View related parts
Ford Taurus Rotor Assembly
Part Number: F4DZ-1125-B
$36.59 MSRP: $49.99
You Save: $13.40 (27%)
ADD TO CART
Product Specifications
- Other Name: ROTOR ASY
- Manufacturer Note: SHO
- Replaced by: YF1Z-1V125-C
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 1995 Ford Taurus | 6 Cyl 3.0L, 6 Cyl 3.2L, 6 Cyl 3.8L | 4AT AX4N, 4AT AX4S, 4AT AXOD-E, 5MT
View related parts
Ford Taurus Rotor Assembly
Part Number: F6DZ-1125-B
$36.59 MSRP: $49.99
You Save: $13.40 (27%)
ADD TO CART
Product Specifications
- Other Name: ROTOR ASY
- Manufacturer Note: exc. SHO - w/aluminum wheels
- Replaced by: YF1Z-1V125-C
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 1996 Ford Taurus | 6 Cyl 3.0L, 8 Cyl 3.4L | 4AT AX4N, 4AT AX4S

| Page 1 of 2 |Next >

1-20 of 34 Results

Ford Taurus Brake Disc

Brake Disc in Ford Taurus automobiles is or is part of the disc brake system where the Brake Pads rub against it to reduce the speed or stop the automobile. Located between the axle or hub to the wheel, through brake operation hydraulic pressure pushes the caliper to squeeze the pads until it touches the rotor. Such a design can be useful for heat dissipation particularly to the vented rotors with cooling fins incorporated in their designs. The following years have seen several Taurus models using Brake Discs of certain types; the solid types as well as the vented kinds. Drum brake rotors are standard in cars that are not performance oriented, while vented rotors are fancier, and improve cooling. Discs are very important because they can get warped, scored, or have excessive runout that can hinder braking. Thus, constant check-ups on the surface of the rotors and replacement of these surfaces when they wear out are crucial to achieving and maintaining the optimal braking power and safety.

We provide a wide range of Ford Taurus Brake Disc at the best prices possible. If you need Ford Taurus Brake Disc, you can shop with confidence on our website. All our OEM parts come with a manufacturer's warranty and are delivered to your door step with a fast delivery service.

Ford Taurus Brake Disc Parts Questions & Experts Answers

Rotor Assembly - Brake
8G1Z-2C026-B
Q: How do I replace and inspect brake discs on a Ford Taurus?
A:
Begin by loosening the wheel lug nuts, raising the vehicle and supporting it securely on jackstands. Remove the Brake Caliper; it isn't necessary to disconnect the brake hose. After removing the caliper bolts, suspend the caliper out of the way with a piece of wire. Visually inspect the disc surface for score marks and other damage. Light scratches and shallow grooves are normal after use but deep scoring requires disc removal and refinishing by an automotive machine shop. Check both sides of the disc.To check disc runout, place a dial indicator at a point about 1/2-inch from the outer edge of the disc. Set the indicator to zero and turn the disc. The indicator reading should not exceed the specified allowable runout limit. If it does, the disc should be refinished by an automotive machine shop. It's recommended to have the discs resurfaced regardless of the dial indicator reading, to impart a smooth finish and ensure a perfectly flat surface. At the very least, remove the glaze from the surface with emery cloth or sandpaper, using a swirling motion.It's absolutely critical that the disc not be machined to a thickness under the specified minimum thickness. The minimum thickness is cast or stamped into the inside of the disc. The disc thickness can be checked with a micrometer. To remove the disc, discard the caliper mounting bracket bolts and remove the bracket. The caliper mounting bracket bolts are one-time use, so always use new ones when installing the caliper. Remove and discard the disc retaining screw and remove the disc.For installation, while the disc is off, wire-brush the backside of the center portion that contacts the wheel hub and clean off any rust or dirt on the hub face. Apply small dots of high-temperature anti-seize around the circumference of the hub, and around the raised center portion. Place the disc in position over the threaded studs, install a new disc retaining screw and tighten to the correct torque. Install the caliper mounting bracket and caliper; use new bolts and tighten them to the correct torque. Install the wheel, then lower the vehicle to the ground. Tighten the lug nuts to the correct torque. Depress the brake pedal a few times to bring the Brake Pads into contact with the disc. Bleeding won't be necessary unless the brake hose was disconnected from the caliper. Check the operation of the brakes carefully before driving the vehicle. If new or resurfaced rear discs are being installed, check the operation of the parking brake.