How to remove and install front shock absorbers on Ford Crown Victoria?

Detach the top end by taking off the attaching nut, washer, and bushing. For 1992 and later models, mark the alignment marks on the adjustment cams before removing the retaining nuts for the upper balljoint. Raise the vehicle, remove self-tapping bolts that attach the lower end of the shock absorber to the lower control arm, and remove the shock absorber through a hole in lower control arm. Replace any worn or damaged parts. To this end, get rid of shock absorber upper mounting nuts, brake caliper, brake disc, stabilizer bar links, balljoint nut and lower mounting bolt for model year 2003 and onward. Check all components for damage and replace them if necessary.

How do you remove the rear shock absorbers on Ford Crown Victoria?

The shock absorbers at the rear should be removed after raising and securing the vehicle's rear on jack stands. With automatic leveling rear suspension and coil springs for older models, let the rear axle hang freely until the shock absorbers finish venting through the compressor. Support the rear axle with a floor jack to keep it from falling when the shock absorbers are detached. For air-assisted shock absorbers, depress the retainer ring(s) and remove the lines by pulling them free. The top of the frame has an upper retaining nut for the shock absorber that can be found. Put an inner insulator and washer on top of it before you get your compressed shock absorber through that hole in this frame. Remove lower retaining nut and lower shock absorber mounting stud from mounting bracket. To make sure all air is expelled from the new shock absorber, extend and compress it several times before installing it.

How to check the Shock Absorber on Ford Crown Victoria?

The steering linkage and suspension components should be checked periodically. Worn or damaged suspension and steering linkage components can result in excessive and abnormal tire wear, poor ride quality, vehicle handling, and reduced fuel economy. To check the shock absorber, park the vehicle on level ground, turn the engine off, and set the parking brake. Check the tire pressures. Push down at one corner of the vehicle, then release it while noting the movement of the body. It should stop moving and come to rest in a level position within one or two bounces. If the vehicle continues to move up and down or if it fails to return to its original position, a worn or weak shock absorber is probably the reason. Repeat the above check at each of the three remaining corners of the vehicle. Raise the vehicle and support it securely on jackstands. Check the shock absorbers for evidence of fluid leakage. A light film of fluid is no cause for concern. Make sure that any fluid noted is from the shocks and not from some other source. If leakage is noted, replace the shocks as a set. Check the shock absorbers to be sure that they are securely mounted and undamaged. Check the upper mounts for damage and wear. If damage or wear is noted, replace the shock absorbers as a set (front or rear). Visually inspect the steering system components for damage and distortion. Look for leaks and damaged seals, boots, and fittings. Clean the lower end of the steering knuckle. Have an assistant grasp the lower edge of the tire and move the wheel in and out while you look for movement at the steering knuckle-to-control arm ball joint. If there is any movement, the suspension ball joint(s) must be replaced. Grasp each front tire at the front and rear edges, push in at the front, pull out at the rear, and feel for play in the steering system components. If any free play is noted, check the steering gear mounts and the tie-rod ends for looseness. Check the steering gear mount bolt tightness. If the tie-rods are loose, the ball joints may be worn.

Genuine Ford Crown Victoria Shock Absorber

Suspension Shock Absorber

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

71 Shock Absorbers found

View related parts
Ford Crown Victoria Shock Absorber Assembly
Part Number: 7W1Z-18125-A
$87.64 MSRP: $147.82
You Save: $60.18 (41%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Shock Absorber Assy
- Replaced by: 8W7Z-18125-D
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2007-2010 Ford Crown Victoria | 8 Cyl 4.6L Romeo SOHC EFI | 4-Speed Automatic Transmission 4R75E Livonia, Left Hand Drive, Rear-Wheel Drive (Left Hand Drive)
View related parts
Ford Crown Victoria Shock Absorber Assembly
Part Number: BW1Z-18125-A
$110.19 MSRP: $150.56
You Save: $40.37 (27%)
ADD TO CART
Product Specifications
- Other Name: Shock Absorber Assy
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2011 Ford Crown Victoria | 8 Cyl 4.6L Romeo SOHC EFI | 4-Speed Automatic Transmission 4R75E Livonia, Left Hand Drive, Rear-Wheel Drive (Left Hand Drive)
View related parts
Ford Crown Victoria Shock Absorber Kit
Part Number: XW7Z-18124-AB
$39.89 MSRP: $54.51
You Save: $14.62 (27%)
ADD TO CART
Product Specifications
- Other Name: Kit - Shock Absorber
- Manufacturer Note: RH & LH, includes XW7Z-18198-AA (AD-953) attaching parts kit., base, standard duty suspension
- Position: Passenger Side & Driver Side
- Replaced by: F8AZ-18124-CA
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 1999-2002 Ford Crown Victoria | 8 Cyl 4.6L | 4AT 4R70W
View related parts
Ford Crown Victoria Shock Absorber Assembly
Part Number: 4W7Z-18125-DA
$87.64 MSRP: $147.82
You Save: $60.18 (41%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Shock Absorber Assy
- Manufacturer Note: RH or LH, ID color: RED, steel wheels, (but not police or taxi), FROM 12/01/03 TO 12/05/05
- Position: Passenger Side Or Driver Side
- Replaced by: 8W7Z-18125-D
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2004-2005 Ford Crown Victoria | 8 Cyl 4.6L | 4AT, 4AT 4R70W, 4AT 4R75W
View related parts
Ford Crown Victoria Shock Absorber Assembly
Part Number: BW7Z-18125-B
$79.58 MSRP: $128.91
You Save: $49.33 (39%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Shock Absorber Assy; Shock, Shock Absorber
- Replaces: 4W7Z-18125-CA, 3U2Z-18125-AB, 7W1Z-18125-G, 3W7Z-18125-FA, 7W7Z-18125-C, 6W7Z-18125-C, 6W7Z-18125-B, 8W1Z-18125-C, ASH-1039, ASH-1040, 8W1Z-18125-A, ASH-24491, 8W1Z-18125-B, ASH-24534, ASH-710, ASH-12276, BW7Z-18125-A, 7W7Z-18125-B, 8W1Z-18125-D, 3U2Z-18125-AF, ASH-1151, ASH-24490, ASH-24535
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2003-2011 Ford Crown Victoria | 8 Cyl 4.6L, 8 Cyl 4.6L Romeo SOHC EFI | 4-Speed Automatic Transmission 4R75E Livonia, 4AT, 4AT 4R70W, 4AT 4R75W, Left Hand Drive, Rear-Wheel Drive (Left Hand Drive)
View related parts
Ford Crown Victoria Shock Absorber Assembly
Part Number: BW7Z-18124-A
$108.76 MSRP: $176.18
You Save: $67.42 (39%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Shock Absorber Assy; Shock Absorber, Strut
- Replaces: 7W7Z-18124-D, 6W7Z-18124-A, 7W7Z-18124-H, ASH-1036, 7W7Z-18124-A, ASH-1037, ASH-24529, BW7Z-18124-B, 6W7Z-18124-B, 6W7Z-18124-D, 7W7Z-18124-C, ASH-1035, ASH-12274
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2006-2011 Ford Crown Victoria | 8 Cyl 4.6L, 8 Cyl 4.6L Romeo SOHC EFI | 4-Speed Automatic Transmission 4R75E Livonia, 4AT, 4AT 4R75W, Left Hand Drive, Rear-Wheel Drive (Left Hand Drive)
View related parts
Ford Crown Victoria Shock Absorber Assembly
Part Number: BW7Z-18124-B
$108.76 MSRP: $176.18
You Save: $67.42 (39%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Shock Absorber Assy
- Replaced by: BW7Z-18124-A
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2011 Ford Crown Victoria | 8 Cyl 4.6L Romeo SOHC EFI | 4-Speed Automatic Transmission 4R75E Livonia, Left Hand Drive, Rear-Wheel Drive (Left Hand Drive)
View related parts
Ford Crown Victoria Shock Absorber Assembly
Part Number: 7W7Z-18124-D
$108.76 MSRP: $176.18
You Save: $67.42 (39%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Shock Absorber Assy
- Replaced by: BW7Z-18124-A
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2007-2011 Ford Crown Victoria | 8 Cyl 4.6L Romeo SOHC EFI | 4-Speed Automatic Transmission 4R75E Livonia, Left Hand Drive, Rear-Wheel Drive (Left Hand Drive)
View related parts
Ford Crown Victoria Shock Absorber Assembly
Part Number: F8AZ-18124-CA
$39.89 MSRP: $54.51
You Save: $14.62 (27%)
ADD TO CART
Product Specifications
- Other Name: Shock Absorber Assy; Shock, Shock Absorber
- Manufacturer Note: RH & LH, heavy duty/Police/Taxi
- Position: Passenger Side & Driver Side
- Replaces: 3U2Z-18124-ZA, AS-1094-G, ASH-702, F8AZ-18124-AA, F8VZ-18124-AA, AS-2028, ASH-24678, XW7Z-18124-AB, XW3Z-18124-AA, XW7Z-18124-A
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 1996-2002 Ford Crown Victoria | 8 Cyl 4.6L | 4AT 4R70W
View related parts
Ford Crown Victoria Shock Absorber Assembly
Part Number: 7W7Z-18125-D
$87.64 MSRP: $147.82
You Save: $60.18 (41%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Shock Absorber Assy
- Replaced by: 8W7Z-18125-D
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2007-2008 Ford Crown Victoria | 8 Cyl 4.6L Romeo SOHC EFI | 4-Speed Automatic Transmission 4R75E Livonia, Left Hand Drive, Rear-Wheel Drive (Left Hand Drive)
View related parts
Ford Crown Victoria Shock Absorber Assembly
Part Number: F8AZ-18124-AA
$39.89 MSRP: $54.51
You Save: $14.62 (27%)
ADD TO CART
Product Specifications
- Other Name: Shock Absorber Assy
- Manufacturer Note: RH & LH, base, standard duty suspension
- Position: Passenger Side & Driver Side
- Replaced by: F8AZ-18124-CA
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 1998-2002 Ford Crown Victoria | 8 Cyl 4.6L | 4AT 4R70W
View related parts
Ford Crown Victoria Shock Absorber Kit
Part Number: XW3Z-18124-AA
$39.89 MSRP: $54.51
You Save: $14.62 (27%)
ADD TO CART
Product Specifications
- Other Name: Kit - Shock Absorber
- Position: Passenger Side & Driver Side
- Replaced by: F8AZ-18124-CA
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 1996-1997 Ford Crown Victoria | 8 Cyl 4.6L | 4AT 4R70W
View related parts
Ford Crown Victoria Shock Absorber Assembly
Part Number: 6W1Z-18125-A
$87.64 MSRP: $147.82
You Save: $60.18 (41%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Shock Absorber Assy
- Position: Passenger Side Or Driver Side
- Replaced by: 8W7Z-18125-D
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2006 Ford Crown Victoria | 8 Cyl 4.6L | 4AT, 4AT 4R75W
View related parts
Ford Crown Victoria Shock Absorber Assembly
Part Number: 6W7Z-18125-D
$87.64 MSRP: $147.82
You Save: $60.18 (41%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Shock Absorber Assy
- Manufacturer Note: RH or LH, steel wheels, fleet (but not police or taxi), color code: RED, FROM 12/05/05 TO 07/31/06
- Position: Passenger Side Or Driver Side
- Replaced by: 8W7Z-18125-D
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2006 Ford Crown Victoria | 8 Cyl 4.6L | 4AT, 4AT 4R75W
View related parts
Ford Crown Victoria Shock Absorber Assembly
Part Number: 3W7Z-18125-GA
$87.64 MSRP: $147.82
You Save: $60.18 (41%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Shock Absorber Assy
- Manufacturer Note: RH or LH, "Red", steel wheels, fleet (but not police or taxi), BEFORE 12/01/03
- Position: Passenger Side Or Driver Side
- Replaced by: 8W7Z-18125-D
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2003-2004 Ford Crown Victoria | 8 Cyl 4.6L | 4AT 4R70W, 4AT 4R75W
View related parts
Ford Crown Victoria Shock Absorber Assembly
Part Number: 4W7Z-18125-CA
$79.58 MSRP: $128.91
You Save: $49.33 (39%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Shock Absorber Assy
- Manufacturer Note: RH or LH, ID color: BLUE, heavy duty suspension, Police, FROM 12/01/03 TO 08/03/05
- Position: Passenger Side Or Driver Side
- Replaced by: BW7Z-18125-B
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2004-2005 Ford Crown Victoria | 8 Cyl 4.6L | 4AT, 4AT 4R70W, 4AT 4R75W
View related parts
Ford Crown Victoria Shock Absorber Assembly
Part Number: 6W7Z-18125-C
$79.58 MSRP: $128.91
You Save: $49.33 (39%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Shock Absorber Assy
- Manufacturer Note: RH or LH, heavy duty suspension, Police, color code: BLUE, FROM 08/03/05 TO 07/31/06
- Position: Passenger Side Or Driver Side
- Replaced by: BW7Z-18125-B
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2006 Ford Crown Victoria | 8 Cyl 4.6L | 4AT, 4AT 4R75W
View related parts
Ford Crown Victoria Shock Absorber Assembly
Part Number: 3W7Z-18125-FA
$79.58 MSRP: $128.91
You Save: $49.33 (39%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Shock Absorber Assy
- Manufacturer Note: RH or LH, "Blue", heavy duty suspension, Police, BEFORE 12/01/03
- Position: Passenger Side Or Driver Side
- Replaced by: BW7Z-18125-B
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2003-2004 Ford Crown Victoria | 8 Cyl 4.6L | 4AT 4R70W, 4AT 4R75W
View related parts
Ford Crown Victoria Shock Absorber Assembly
Part Number: 3U2Z-18125-AF
$79.58 MSRP: $128.91
You Save: $49.33 (39%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Shock Absorber Assy
- Manufacturer Note: RH or LH, "Blue" (replaced 3W7Z-18125-FA), heavy duty suspension, Police, BEFORE 12/01/03
- Position: Passenger Side Or Driver Side
- Replaced by: BW7Z-18125-B
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2003-2004 Ford Crown Victoria | 8 Cyl 4.6L | 4AT 4R70W, 4AT 4R75W
View related parts
Ford Crown Victoria Shock Absorber Kit
Part Number: XW7Z-18125-CA
Product Specifications
- Other Name: Kit - Shock Absorber; Shock, Shock Absorber
- Manufacturer Note: RH or LH, with air springs
- Position: Passenger Side Or Driver Side
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 1992-1997 Ford Crown Victoria | 8 Cyl 4.6L | 4AT 4R70W, 4AT AOD, 4AT AOD-E

| Page 1 of 4 |Next >

1-20 of 71 Results

Ford Crown Victoria Shock Absorber

The Shock Absorber of Ford Crown Victoria vehicles involves in the Suspension system of the vehicle and works in conjunction with the struts. These components play the mainly role in avoiding bouncing as well as dampening the shock impulses resulting in enhanced ride quality and control. In recent years, there have been many developments in the style of shock absorber including twin tube and mono tube and interestingly the levels of control are provided by the hydraulic fluid in the shock absorber depending on type of driving that is being conducted. Some of the simplest and most primitive systems include the gas-charged twin-tube shocks but have also gone through more developed kinds like the Position Sensitive Damping (PSD) and Acceleration Sensitive Damping (ASD) kinds of shock absorbers anchored on Ford Crown Victoria vehicles to optimize for comfort as well as control on the road.

We provide a wide range of Ford Crown Victoria Shock Absorber at the optimal prices. If you need Ford Crown Victoria Shock Absorber, you can shop with confidence on our website. All our OEM parts come with a manufacturer's warranty and are delivered to your doorstep with a fast delivery service.

Ford Crown Victoria Shock Absorber Parts Questions & Experts Answers

Strut Loaded Assembly
GU2Z-18A092-AH
Q: How to remove and install front shock absorbers on Ford Crown Victoria?
A:
Detach the top end by taking off the attaching nut, washer, and bushing. For 1992 and later models, mark the alignment marks on the adjustment cams before removing the retaining nuts for the upper balljoint. Raise the vehicle, remove self-tapping bolts that attach the lower end of the shock absorber to the lower Control Arm, and remove the shock absorber through a hole in lower control arm. Replace any worn or damaged parts. To this end, get rid of shock absorber upper mounting nuts, brake caliper, brake disc, stabilizer bar links, balljoint nut and lower mounting bolt for model year 2003 and onward. Check all components for damage and replace them if necessary.
Shock Absorber Kit
5U2Z-18V125-C
Q: How do you remove the rear shock absorbers on Ford Crown Victoria?
A:
The shock absorbers at the rear should be removed after raising and securing the vehicle's rear on jack stands. With automatic leveling rear suspension and coil springs for older models, let the rear axle hang freely until the shock absorbers finish venting through the compressor. Support the rear axle with a floor jack to keep it from falling when the shock absorbers are detached. For air-assisted shock absorbers, depress the retainer ring(s) and remove the lines by pulling them free. The top of the frame has an upper retaining nut for the shock absorber that can be found. Put an inner insulator and washer on top of it before you get your compressed shock absorber through that hole in this frame. Remove lower retaining nut and lower shock absorber mounting stud from mounting bracket. To make sure all air is expelled from the new shock absorber, extend and compress it several times before installing it.
Shock Absorber Assembly
BW7Z-18124-B
Q: How to check the Shock Absorber on Ford Crown Victoria?
A:
The steering linkage and suspension components should be checked periodically. Worn or damaged suspension and steering linkage components can result in excessive and abnormal tire wear, poor ride quality, vehicle handling, and reduced fuel economy. To check the shock absorber, park the vehicle on level ground, turn the engine off, and set the parking brake. Check the tire pressures. Push down at one corner of the vehicle, then release it while noting the movement of the body. It should stop moving and come to rest in a level position within one or two bounces. If the vehicle continues to move up and down or if it fails to return to its original position, a worn or weak shock absorber is probably the reason. Repeat the above check at each of the three remaining corners of the vehicle. Raise the vehicle and support it securely on jackstands. Check the shock absorbers for evidence of fluid leakage. A light film of fluid is no cause for concern. Make sure that any fluid noted is from the shocks and not from some other source. If leakage is noted, replace the shocks as a set. Check the shock absorbers to be sure that they are securely mounted and undamaged. Check the upper mounts for damage and wear. If damage or wear is noted, replace the shock absorbers as a set (front or rear). Visually inspect the steering system components for damage and distortion. Look for leaks and damaged seals, boots, and fittings. Clean the lower end of the steering knuckle. Have an assistant grasp the lower edge of the tire and move the wheel in and out while you look for movement at the steering knuckle-to-control arm ball joint. If there is any movement, the suspension ball joint(s) must be replaced. Grasp each front tire at the front and rear edges, push in at the front, pull out at the rear, and feel for play in the steering system components. If any free play is noted, check the steering gear mounts and the tie-rod ends for looseness. Check the steering gear mount bolt tightness. If the tie-rods are loose, the ball joints may be worn.