How to drain and replace the Transmission Filter on the Ford Crown Victoria?

At the specified intervals, the transmission fluid should be drained and replaced. Since the fluid will remain hot long after driving, perform this procedure only after the engine has cooled down completely. Before beginning work, purchase the transmission fluid specified in Recommended lubricants and fluids, a new filter, and gaskets. Never reuse the old filter or gasket! Other tools necessary for this job include jackstands to support the vehicle in a raised position, a drain pan capable of holding at least eight quarts, newspapers, and clean rags. Raise the vehicle and support it securely on jackstands. With the drain pan in place, remove the front and side transmission pan mounting bolts. Loosen the rear pan bolts approximately four turns. Carefully pry the transmission pan loose with a screwdriver, allowing the fluid to drain. Don't damage the pan or transmission gasket surfaces, or leaks could develop. Remove the remaining bolts, pan, and gasket. Carefully clean the gasket surface of the transmission to remove all traces of the old gasket and sealant. Drain the fluid from the transmission pan, clean it with solvent, and dry it with compressed air. Remove the filter from the mount inside the transmission. Install a new seal, gasket, and filter. Tighten the mounting bolts securely. Make sure the gasket surface on the transmission pan is clean, then install a new gasket. Put the pan in place against the transmission and install the bolts. Working around the pan, tighten each bolt a little at a time until the final torque figure is reached. Don't overtighten the bolts! Lower the vehicle and add about four or five pints of automatic transmission fluid through the filler tube. With the transmission in Park and the parking brake set, run the engine at a fast idle, but don't race it. Move the gear selector through each range and back to Park. Check the fluid level. Add fluid if needed to reach the correct level. Check under the vehicle for leaks during the first few trips.

Genuine Ford Crown Victoria Transmission Filter

Automatic Transmission Filter

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

9 Transmission Filters found

View related parts
Ford Crown Victoria Filter
Part Number: F6AZ-7A098-A
$25.03 MSRP: $40.55
You Save: $15.52 (39%)
Ships in 1 Business Day
ADD TO CART
Product Specifications
- Other Name: Filter Assembly; Filter, Screen
- Replaces: F4TZ-7A098-A
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2007-2011 Ford Crown Victoria | 8 Cyl 4.6L Romeo SOHC EFI | 4-Speed Automatic Transmission 4R75E Livonia, Left Hand Drive, Rear-Wheel Drive (Left Hand Drive)
- 1996-2004 Ford Crown Victoria | 8 Cyl 4.6L | 4AT 4R70W
View related parts
Ford Crown Victoria Oil Filter Assembly
Part Number: XC3Z-7B155-G
$36.67 MSRP: $60.18
You Save: $23.51 (40%)
ADD TO CART
Product Specifications
- Other Name: Filter Assembly - Oil
- Replaces: F8DZ-3F595-AA, FT-116, XC3Z-7B155-BA, XC3Z-7B155-D
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2007-2011 Ford Crown Victoria | 8 Cyl 4.6L Romeo SOHC EFI | 4-Speed Automatic Transmission 4R75E Livonia, Left Hand Drive, Rear-Wheel Drive (Left Hand Drive)
- 2003-2004 Ford Crown Victoria | 8 Cyl 4.6L | 4AT 4R70W
View related parts
Ford Crown Victoria Transmission Fluid Kit
Part Number: XC3Z-7B155-E
$90.88 MSRP: $153.27
You Save: $62.39 (41%)
ADD TO CART
Product Specifications
- Other Name: Kit - Transmission Fluid External Filter
- Replaced by: XC3Z-7B155-F
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2007-2008 Ford Crown Victoria | 8 Cyl 4.6L Romeo SOHC EFI | 4-Speed Automatic Transmission 4R75E Livonia, Left Hand Drive, Rear-Wheel Drive (Left Hand Drive)
View related parts
Ford Crown Victoria Filter Assembly
Part Number: XC3Z-7B155-F
$90.88 MSRP: $153.27
You Save: $62.39 (41%)
ADD TO CART
Product Specifications
- Other Name: Kit - Transmission Fluid External Filter; Filter Assembly
- Replaces: XC3Z-7B155-CA, XC3Z-7B155-E
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2007-2011 Ford Crown Victoria | 8 Cyl 4.6L Romeo SOHC EFI | 4-Speed Automatic Transmission 4R75E Livonia, Left Hand Drive, Rear-Wheel Drive (Left Hand Drive)
- 2004 Ford Crown Victoria | 8 Cyl 4.6L | 4AT 4R70W
View related parts
Ford Crown Victoria Oil Filter Assembly
Part Number: XC3Z-7B155-CA
$90.88 MSRP: $153.27
You Save: $62.39 (41%)
ADD TO CART
Product Specifications
- Other Name: Filter Assembly - Oil
- Replaced by: XC3Z-7B155-F
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2004 Ford Crown Victoria | 8 Cyl 4.6L | 4AT 4R70W
View related parts
Ford Crown Victoria Oil Filter Assembly
Part Number: XC3Z-7B155-BA
$36.67 MSRP: $60.18
You Save: $23.51 (40%)
ADD TO CART
Product Specifications
- Other Name: Filter Assembly - Oil
- Replaced by: XC3Z-7B155-G
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2003-2004 Ford Crown Victoria | 8 Cyl 4.6L | 4AT 4R70W
View related parts
Ford Crown Victoria Oil Filter Assembly
Part Number: XC3Z-7B155-D
$36.67 MSRP: $60.18
You Save: $23.51 (40%)
ADD TO CART
Product Specifications
- Other Name: Filter Assembly - Oil
- Replaced by: XC3Z-7B155-G
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2007-2008 Ford Crown Victoria | 8 Cyl 4.6L Romeo SOHC EFI | 4-Speed Automatic Transmission 4R75E Livonia, Left Hand Drive, Rear-Wheel Drive (Left Hand Drive)
View related parts
Ford Crown Victoria Screen Assembly
Part Number: F2VY-7A098-A
Product Specifications
- Other Name: Screen Assy; Filter
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 1992 Ford Crown Victoria | 8 Cyl 4.6L | 4AT AOD, 4AT AOD-E
View related parts
Ford Crown Victoria Screen Assembly
Part Number: E1AZ-7A098-A
Product Specifications
- Other Name: Screen Assy; Filter, Filter Kit
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 1992 Ford Crown Victoria | 8 Cyl 4.6L | 4AT AOD, 4AT AOD-E

Ford Crown Victoria Transmission Filter

We provide a wide range of Ford Crown Victoria Transmission Filter at the optimal prices. If you need Ford Crown Victoria Transmission Filter, you can shop with confidence on our website. All our OEM parts come with a manufacturer's warranty and are delivered to your doorstep with a fast delivery service.

Ford Crown Victoria Transmission Filter Parts Questions & Experts Answers

Filter
F6AZ-7A098-A
Q:
How to drain and replace the Transmission Filter on the Ford Crown Victoria?
Posted by Elwin R.
A:
At the specified intervals, the transmission fluid should be drained and replaced. Since the fluid will remain hot long after driving, perform this procedure only after the engine has cooled down completely. Before beginning work, purchase the transmission fluid specified in Recommended lubricants and fluids, a new filter, and gaskets. Never reuse the old filter or gasket! Other tools necessary for this job include jackstands to support the vehicle in a raised position, a drain pan capable of holding at least eight quarts, newspapers, and clean rags. Raise the vehicle and support it securely on jackstands. With the drain pan in place, remove the front and side transmission pan mounting bolts. Loosen the rear pan bolts approximately four turns. Carefully pry the transmission pan loose with a screwdriver, allowing the fluid to drain. Don't damage the pan or transmission gasket surfaces, or leaks could develop. Remove the remaining bolts, pan, and gasket. Carefully clean the gasket surface of the transmission to remove all traces of the old gasket and sealant. Drain the fluid from the transmission pan, clean it with solvent, and dry it with compressed air. Remove the filter from the mount inside the transmission. Install a new seal, gasket, and filter. Tighten the mounting bolts securely. Make sure the gasket surface on the transmission pan is clean, then install a new gasket. Put the pan in place against the transmission and install the bolts. Working around the pan, tighten each bolt a little at a time until the final torque figure is reached. Don't overtighten the bolts! Lower the vehicle and add about four or five pints of automatic transmission fluid through the filler tube. With the transmission in Park and the parking brake set, run the engine at a fast idle, but don't race it. Move the gear selector through each range and back to Park. Check the fluid level. Add fluid if needed to reach the correct level. Check under the vehicle for leaks during the first few trips.
Answered by Ford Parts Specialist Bastien / Jul 09, 2023

Related Ford Crown Victoria Parts

Browse by Year

2011 Transmission Filter 2010 Transmission Filter 2009 Transmission Filter 2008 Transmission Filter 2007 Transmission Filter 2004 Transmission Filter 2003 Transmission Filter 2002 Transmission Filter 2001 Transmission Filter 2000 Transmission Filter 1999 Transmission Filter 1998 Transmission Filter 1997 Transmission Filter 1996 Transmission Filter 1992 Transmission Filter