How to remove and install a hood latch and Hood Cable on a Mercury Mariner?

To install new hood latches for vehicles 2005 or newer, draw lines around the hood hinges before you start, so you can exactly place the latch back later. Only undo, but do not remove, the nut, then remove the bolts that hold the hood latch in place. Pull the insulating plastic tube off the latch cable, disconnect its end, and take out the latch. To install the hood, line everything up again, push down on the bumper until the hood latches stay in place when you shut it. Inside the passenger cabin, take off the driver kick panel, lift the hood release handle lever, turn the cable housing end, and pull the cable out from the handle. Pull off the mounting bolts if needed, first from the dashboard, to take off the hood release handle completely. Before starting, attach a wire or string to the end of the cable. Inside the engine area, take out the Hood Cable from the latch on its holder. Also detach every small wire holding the cable in place on the radiator support's back and fender well.

Genuine Mercury Mariner Hood Latch

Engine Hood Latch

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

3 Hood Latches found

View related parts
Mercury Mariner Hood Latch Assembly
Part Number: 8L8Z-16700-A
$31.30 MSRP: $44.58
You Save: $13.28 (30%)
Ships in 1 Business Day
ADD TO CART
Product Specifications
- Other Name: Latch Assy - Hood; Latch, Lock
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2008-2011 Mercury Mariner | 4 Cyl 2.3L, 4 Cyl 2.3L Hybrid Gas/Electric DOHC, 4 Cyl 2.5L Duratec (110kW/150PS), 4 Cyl 2.5L PFI Gas/Electric, 6 Cyl 3.0L DOHC EFI Modular, 6 Cyl 3.0L OHC Duratec | 4AT CD4E, 5-Speed Manual Transmission - AK, 6-Speed Automatic Transmission 6F Mid-Range, CVT Auto Trans Powersplit Elec, Four-Wheel Drive (Full Time) (Left Hand Drive), Front-Wheel Drive (Left Hand Drive), Left Hand Drive
View related parts
Mercury Mariner Hood Latch Assembly
Part Number: 6L8Z-16700-B
Product Specifications
- Other Name: Latch Assy - Hood; Latch, Lock
- Replaces: 6L8Z-16700-A
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2006-2007 Mercury Mariner | 4 Cyl 2.3L, 4 Cyl 2.3L Hybrid Gas/Electric DOHC, 6 Cyl 3.0L DOHC EFI Modular | 4AT CD4E, 5-Speed Manual Transmission, 5-Speed Manual Transmission - AK, 6-Speed Automatic Transmission 6F Mid-Range, CVT Auto Trans Powersplit Elec, Four-Wheel Drive (Full Time) (Left Hand Drive), Four-Wheel Drive (Right Hand Drive), Front-Wheel Drive (Left Hand Drive), Left Hand Drive, Two-Wheel Drive (Left Hand Drive), Two-Wheel Drive (Right Hand Drive)
View related parts
Mercury Mariner Hood Latch Assembly
Part Number: 6L8Z-16700-A
Product Specifications
- Other Name: Latch Assy - Hood
- Replaced by: 6L8Z-16700-B
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2006 Mercury Mariner | 4 Cyl 2.3L, 4 Cyl 2.3L Hybrid Gas/Electric DOHC, 6 Cyl 3.0L DOHC EFI Modular | 4AT CD4E, 5-Speed Manual Transmission, 5-Speed Manual Transmission - AK, CVT Auto Trans Powersplit Elec, Four-Wheel Drive (Full Time) (Left Hand Drive), Four-Wheel Drive (Right Hand Drive), Front-Wheel Drive (Left Hand Drive), Left Hand Drive, Two-Wheel Drive (Left Hand Drive), Two-Wheel Drive (Right Hand Drive)

Mercury Mariner Hood Latch

The Hood Latch of Mercury Mariner cars is an important part located on the underside front of the hood used to hold the hood in place while in use. This mechanism is important to ensure that the vehicles critical components for instance the engine, the radiator, the battery among others are protected from being exposed by the hoods while the vehicle is in motion. Depending on the type of Mercury Mariner car, various types or kinds of Hood Latch could have been used throughout the progression of the models each with their own design and purpose to ensure that the hood of the car stays shut during the use of the vehicle.

We provide a wide range of Mercury Mariner Hood Latch at the optimal prices. If you need Mercury Mariner Hood Latch, you can shop with confidence on our website. All our OEM parts come with a manufacturer's warranty and are delivered to your doorstep with a fast delivery service.

Mercury Mariner Hood Latch Parts Questions & Experts Answers

Hood Latch Assembly
8L8Z-16700-A
Q: How to remove and install a hood latch and Hood Cable on a Mercury Mariner?
A:
To install new hood latches for vehicles 2005 or newer, draw lines around the Hood Hinges before you start, so you can exactly place the latch back later. Only undo, but do not remove, the nut, then remove the bolts that hold the hood latch in place. Pull the insulating plastic tube off the latch cable, disconnect its end, and take out the latch. To install the hood, line everything up again, push down on the bumper until the hood latches stay in place when you shut it. Inside the passenger cabin, take off the driver kick panel, lift the hood release handle lever, turn the cable housing end, and pull the cable out from the handle. Pull off the mounting bolts if needed, first from the dashboard, to take off the hood release handle completely. Before starting, attach a wire or string to the end of the cable. Inside the engine area, take out the Hood Cable from the latch on its holder. Also detach every small wire holding the cable in place on the radiator support's back and fender well.