How to remove and install the front Sway Bar Kit on a Ford Crown Victoria?

To ensure that the vehicle does not drop, lift it up and put it on stands, securely. Disconnect the nut from each end of the sway bar kit and take it off from the links. In 1988-1991 models, the lower control arms act as a bridge between the links and the sway bar kits. On 1992 and after this, they are attached to the steering knuckles. Detach the nut from each end to disconnect the sway bar kit from the links. In 2006, remove shock absorber/coil spring assembly. Unfasten nuts clamping down on sway bar kit clamps. Detach nuts holding bushing clamps attaching bar to the frame if you want to detach the frame from the sway bar kit. Remove bar that stabilizes the car during motion. The process of fitting back is the reverse of removal. Fasten all screws firmly as required by the manufacturer's specifications.

Genuine Ford Crown Victoria Sway Bar Kit

Stabilizer Sway Bar Set

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

17 Sway Bar Kits found

View related parts
Ford Crown Victoria Stabilizer Bar
Part Number: 3W1Z-5A772-AA
$98.66 MSRP: $137.06
You Save: $38.40 (29%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Bar - Stabilizer; Stabilizer Bar
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2003-2011 Ford Crown Victoria | 8 Cyl 4.6L, 8 Cyl 4.6L Romeo SOHC EFI | 4AT, 4AT 4R70W, 4AT 4R75W, 4-Speed Automatic Transmission 4R75E Livonia, Left Hand Drive, Rear-Wheel Drive (Left Hand Drive)
View related parts
Ford Crown Victoria Rear Stabilizer Bar
Part Number: 6W1Z-4264-B
$206.42 MSRP: $305.00
You Save: $98.58 (33%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Bar - Rear Stabilizer
- Manufacturer Note: (replacing the 6W1Z-4264-AA), FROM 08/03/05
- Position: Rear
- Replaced by: 8W1Z-4264-B
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2006-2009 Ford Crown Victoria | 8 Cyl 4.6L, 8 Cyl 4.6L Romeo SOHC EFI | 4AT, 4AT 4R75W, 4-Speed Automatic Transmission 4R75E Livonia, Left Hand Drive, Rear-Wheel Drive (Left Hand Drive)
View related parts
Ford Crown Victoria Rear Stabilizer Bar
Part Number: 5W1Z-4264-B
$206.42 MSRP: $305.00
You Save: $98.58 (33%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Bar - Rear Stabilizer
- Manufacturer Note: (replaced by 6W1Z-4264-B), FROM 11/29/04 TO 08/03/05
- Position: Rear
- Replaced by: 8W1Z-4264-B
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2005 Ford Crown Victoria | 8 Cyl 4.6L | 4AT
View related parts
Ford Crown Victoria Stabilizer Bar
Part Number: YW7Z-5A772-CA
$510.17 MSRP: $708.71
You Save: $198.54 (29%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Bar - Stabilizer; Stabilizer Bar
- Manufacturer Note: Diameter, 21 mm , sport equipment package or handling package (up,sized rear stabilizer bar)
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2001-2006 Ford Crown Victoria | 8 Cyl 4.6L | 4AT, 4AT 4R70W, 4AT 4R75W
View related parts
Ford Crown Victoria Stabilizer Bar
Part Number: YW7Z-5A772-AA
$166.85 MSRP: $246.53
You Save: $79.68 (33%)
ADD TO CART
Product Specifications
- Other Name: Bar - Stabilizer; Stabilizer Bar
- Replaces: F8AZ-5A772-AA
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 1998-2011 Ford Crown Victoria | 8 Cyl 4.6L, 8 Cyl 4.6L Romeo SOHC EFI | 4-Speed Automatic Transmission 4R75E Livonia, 4AT, 4AT 4R70W, 4AT 4R75W, Left Hand Drive, Rear-Wheel Drive (Left Hand Drive)
View related parts
Ford Crown Victoria Stabilizer Bar
Part Number: F8AZ-5A772-AA
$166.85 MSRP: $246.53
You Save: $79.68 (33%)
ADD TO CART
Product Specifications
- Other Name: Bar - Stabilizer
- Replaced by: YW7Z-5A772-AA
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 1998-2000 Ford Crown Victoria | 8 Cyl 4.6L | 4AT 4R70W
View related parts
Ford Crown Victoria Rear Stabilizer Bar
Part Number: 6W1Z-4264-AA
$206.42 MSRP: $305.00
You Save: $98.58 (33%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Bar - Rear Stabilizer
- Manufacturer Note: (being replaced by the 6W1Z-4264-B), FROM 08/03/05
- Position: Rear
- Replaced by: 8W1Z-4264-B
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2006 Ford Crown Victoria | 8 Cyl 4.6L | 4AT, 4AT 4R75W
View related parts
Ford Crown Victoria Front Stabilizer Bar
Part Number: F8AZ-5482-DA
Product Specifications
- Other Name: Bar - Front Stabilizer; Stabilizer Bar
- Position: Front
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 1998-2002 Ford Crown Victoria | 8 Cyl 4.6L | 4AT 4R70W
View related parts
Ford Crown Victoria Stabilizer Bar
Part Number: YW7Z5482AA
Product Specifications
- Other Name: Bar Assembly - Roll; Stabilizer Bar
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 1999-2002 Ford Crown Victoria | 8 Cyl 4.6L | 4AT 4R70W
View related parts
Ford Crown Victoria Stabilizer Bar
Part Number: FOVY5A772A
Product Specifications
- Other Name: Bar - Stabilizer; Stabilizer Bar
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 1995-1997 Ford Crown Victoria | 8 Cyl 4.6L | 4AT 4R70W, 4AT AOD-E
- 1992 Ford Crown Victoria | 8 Cyl 4.6L | 4AT AOD, 4AT AOD-E
View related parts
Ford Crown Victoria Roll Bar Assembly
Part Number: F8AZ5482AA
Product Specifications
- Other Name: Bar Assy - Roll; Stabilizer Bar
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 1998-2002 Ford Crown Victoria | 8 Cyl 4.6L | 4AT 4R70W
View related parts
Ford Crown Victoria Stabilizer Bar
Part Number: F1VY-5A772-A
Product Specifications
- Other Name: Bar - Stabilizer; Stabilizer Bar
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 1992-2003 Ford Crown Victoria | 8 Cyl 4.6L | 4AT 4R70W, 4AT AOD, 4AT AOD-E
View related parts
Ford Crown Victoria Stabilizer Bar
Part Number: AW1Z-5482-C
Product Specifications
- Other Name: Bar - Stabilizer; Stabilizer Bar
- Manufacturer Note: Ø 29MM
- Replaces: 7W1Z-5482-D
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2006-2011 Ford Crown Victoria | 8 Cyl 4.6L, 8 Cyl 4.6L Romeo SOHC EFI | 4-Speed Automatic Transmission 4R75E Livonia, 4AT, 4AT 4R75W, Left Hand Drive, Rear-Wheel Drive (Left Hand Drive)
View related parts
Ford Crown Victoria Stabilizer Bar
Part Number: AW1Z-5482-A
Product Specifications
- Other Name: Bar - Stabilizer; Stabilizer Bar
- Manufacturer Note: 'Ø 26.5MM'
- Replaces: 6W1Z-5482-F, 7W1Z-5482-B
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2007-2011 Ford Crown Victoria | 8 Cyl 4.6L Romeo SOHC EFI | 4-Speed Automatic Transmission 4R75E Livonia, Left Hand Drive, Rear-Wheel Drive (Left Hand Drive)
View related parts
Ford Crown Victoria Roll Bar Assembly
Part Number: 7W1Z-5482-D
Product Specifications
- Other Name: Bar Assy - Roll
- Replaced by: AW1Z-5482-C
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2006-2010 Ford Crown Victoria | 8 Cyl 4.6L, 8 Cyl 4.6L Romeo SOHC EFI | 4AT, 4AT 4R75W, 4-Speed Automatic Transmission 4R75E Livonia, Left Hand Drive, Rear-Wheel Drive (Left Hand Drive)
View related parts
Ford Crown Victoria Roll Bar Assembly
Part Number: 7W1Z-5482-B
Product Specifications
- Other Name: Bar Assy - Roll; Stabilizer Bar
- Manufacturer Note: 'Ø 26.5MM'
- Replaced by: AW1Z-5482-A
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2007-2010 Ford Crown Victoria | 8 Cyl 4.6L Romeo SOHC EFI | 4-Speed Automatic Transmission 4R75E Livonia, Left Hand Drive, Rear-Wheel Drive (Left Hand Drive)
View related parts
Ford Crown Victoria Roll Bar Assembly
Part Number: 3W7Z-5482-DA
Product Specifications
- Other Name: Bar Assy - Roll; Stabilizer Bar
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2003-2004 Ford Crown Victoria | 8 Cyl 4.6L | 4AT 4R70W, 4AT 4R75W

Ford Crown Victoria Sway Bar Kit

Sway Bar Kit is used to connect different sides of the suspension system of the vehicle so as to improve on handling of the car especially of the Ford Crown Victoria brand. This kit is mostly used to minimize some rocking or lateral movement of the car during high speed turns and over surfaces that are irregular or bumpy with an overall view of enhancing stability. The Sway Bar Kit part, the anti-roll bar, functions against torsion in a manner that keeps the height of the wheels of the vehicle similar generally and providing less sideways tilt. There have been many styles of Sway Bar Kits used in Ford Crown Victoria over the years, the main differences being in the amount of adjustment allowed, and the degree of stiffness. Standard suspension kits give predictable performance while adjustable, active anti-roll bars provide variable stiffness for racing or other high-performance situations. These modifications improve stabiliser and road feel, making the Sway Bar Kit as an integral part of the Ford Crown Victoria.

We provide a wide range of Ford Crown Victoria Sway Bar Kit at the optimal prices. If you need Ford Crown Victoria Sway Bar Kit, you can shop with confidence on our website. All our OEM parts come with a manufacturer's warranty and are delivered to your doorstep with a fast delivery service.

Ford Crown Victoria Sway Bar Kit Parts Questions & Experts Answers

Stabilizer Bar
F8AZ-5A772-AA
Q:
How to remove and install the front Sway Bar Kit on a Ford Crown Victoria?
Posted by Bucky K.
A:
To ensure that the vehicle does not drop, lift it up and put it on stands, securely. Disconnect the nut from each end of the sway bar kit and take it off from the links. In 1988-1991 models, the lower Control Arms act as a bridge between the links and the sway bar kits. On 1992 and after this, they are attached to the Steering Knuckles. Detach the nut from each end to disconnect the sway bar kit from the links. In 2006, remove shock absorber/Coil Spring assembly. Unfasten nuts clamping down on sway bar kit clamps. Detach nuts holding bushing clamps attaching bar to the frame if you want to detach the frame from the sway bar kit. Remove bar that stabilizes the car during motion. The process of fitting back is the reverse of removal. Fasten all screws firmly as required by the manufacturer's specifications.
Answered by Ford Parts Specialist Joseph / Jun 30, 2022