My Garage
My Account
Cart
Genuine Ford Crown Victoria Engine Mount
Engine Motor Mount- Select Vehicle by Model
- Select Vehicle by VIN
Select Vehicle by Model
orMake
Model
Year
Select Vehicle by VIN
For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).
10 Engine Mounts found
Ford Crown Victoria Engine Support Insulator Assembly
Part Number: 3W1Z-6038-BA$67.49 MSRP: $98.67You Save: $31.18 (32%)
Ford Crown Victoria Engine Support Insulator Assembly
Part Number: 1W7Z-6038-BA$63.28 MSRP: $87.90You Save: $24.62 (29%)Ships in 1-2 Business Days
Ford Crown Victoria Engine Support Insulator Assembly
Part Number: F8VZ-6068-AA$146.88 MSRP: $204.04You Save: $57.16 (29%)Ships in 1-2 Business DaysFord Crown Victoria Insulator Assembly Engine S
Part Number: F2AZ6068B$49.91 MSRP: $68.20You Save: $18.29 (27%)
Ford Crown Victoria Front Mount
Part Number: 3W7Z-6038-AA$72.79 MSRP: $96.83You Save: $24.04 (25%)Ships in 1-2 Business Days
Ford Crown Victoria Insulator Assembly
Part Number: F4AZ-6038-A$53.11 MSRP: $73.78You Save: $20.67 (29%)Ships in 1-2 Business Days
Ford Crown Victoria Transmission Mount
Part Number: 3W1Z-6068-BA$50.23 MSRP: $72.17You Save: $21.94 (31%)
Ford Crown Victoria Engine Mount
The Ford Crown Victoria Engine Mount acts like a quiet guard for the car, anchoring the V8 powertrain and absorbing shakes and rumbles. Every Ford Crown Victoria uses a classic design consisting of two steel brackets separated by a thick rubber core. This Engine Mount sandwiches the engine and frame so the sedan remains smooth over bumpy pavement. Earlier models were fitted with solid rubber components, but later police-package versions can be found with hydraulic styles. These hydraulic types use a more advanced Engine Mount that injects fluid into the insulator for more vibration soaking without allowing the engine to wander under hard pursuit. The updated electronic active choice across the range represents the peak Engine Mount evolution, staying soft at idle while hardening as revs lift, giving the big sedan both calm and control. No matter the application, all Ford Crown Victorias depend upon a healthy Engine Mount to avoid expensive metal-on-metal clunks, misaligned driveline angles, and costly component breakage. Thus, cracked rubber, leaking fluid, and separated plates are all a sign for immediate change. Routine visual inspections under the hood of any Ford Crown Victoria can catch sagging mounts before excessive vibration enters the cabin.
We provide a wide range of Ford Crown Victoria Engine Mount at the optimal prices. If you need Ford Crown Victoria Engine Mount, you can shop with confidence on our website. All our OEM parts come with a manufacturer's warranty and are delivered to your doorstep with a fast delivery service.
Ford Crown Victoria Engine Mount Parts Questions & Experts Answers
- Q: What should be done if engine mounts are broken or deteriorated in 5.0L V8 engine on Ford Crown Victoria?A:Engine mounts seldom require attention, but broken or deteriorated mounts should be replaced immediately to prevent damage or wear on driveline components. To check the mounts, raise the engine slightly to remove the weight from them. Begin by raising the vehicle and securely supporting it on jackstands, then position a jack under the engine oil pan with a large block of wood in between. Carefully raise the engine just enough to relieve the weight on the mounts. Inspect the mounts for any cracks, hardened rubber, or separation from the metal plates, noting that the rubber may split down the center. Check for any relative movement between the mount plates and the engine or frame using a large screwdriver or prybar; if movement is detected, lower the engine and tighten the mount fasteners. Applying rubber preservative can help slow deterioration. For replacement, disconnect the negative battery cable, raise the vehicle, and support it securely on jackstands if not already done. Remove the nut to disconnect the mount from the frame and disconnect the automatic transmission shift linkage. Raise the engine slightly with a jack or hoist, ensuring the fan does not hit the radiator or shroud, then remove the mount-to-block bolts and detach the mount. Installation follows the reverse order of removal, using thread locking compound on the mount bolts and tightening them to the specified torque.
Related Ford Crown Victoria Parts
Browse by Year
2011 Engine Mount 2010 Engine Mount 2009 Engine Mount 2008 Engine Mount 2007 Engine Mount 2006 Engine Mount 2005 Engine Mount 2004 Engine Mount 2003 Engine Mount 2002 Engine Mount 2001 Engine Mount 2000 Engine Mount 1999 Engine Mount 1998 Engine Mount 1997 Engine Mount 1996 Engine Mount 1995 Engine Mount 1994 Engine Mount 1993 Engine Mount 1992 Engine Mount