How to perform a resistance check and replace the antenna on Ford Crown Victoria?

To perform a resistance check, ensure the antenna cable is installed on the vehicle and unplugged from the radio, then use an ohmmeter to check the antenna between the cable and tip, expecting a reading of less than 5 ohms; if the reading is higher, replace the antenna and cable assembly. For replacement, first disconnect the cable from the negative battery terminal. For a power antenna, lower the antenna, remove the rear screws from the right side front splash shield for access, and take out the lower antenna bolt. Next, remove the nut at the top of the antenna stanchion and lower the antenna through the fender opening, using needle nose pliers to unscrew the antenna stanchion nut. Installation follows the reverse order of removal. For a manual antenna, detach the antenna lead retaining clips in the engine compartment, remove the screws, and detach the right cowl side trim panel. Then, remove the radio and unplug the antenna lead cable, take off the radio antenna base cap, remove the mounting screws, and pull the base and cable assembly through the fender opening into the engine compartment, with installation again being the reverse of removal.

Genuine Ford Crown Victoria Antenna

Radio Antenna

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

6 Antennas found

View related parts
Ford Crown Victoria Rod Assembly - Replacement - Aerial
Part Number: D3AZ-18A886-A
$17.29 MSRP: $24.63
You Save: $7.34 (30%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Rod Assy - Replacement - Aerial; Antenna Mast, Mast
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 1992-1994 Ford Crown Victoria | 8 Cyl 4.6L | 4AT AOD, 4AT AOD-E
View related parts
Ford Crown Victoria Aerial Kit
Part Number: 5C3Z-18813-AA
$31.16 MSRP: $45.55
You Save: $14.39 (32%)
ADD TO CART
Product Specifications
- Other Name: Kit - Aerial
- Replaced by: MCPZ-18813-D
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2005 Ford Crown Victoria | 8 Cyl 4.6L | 4AT
View related parts
Ford Crown Victoria Aerial Kit
Part Number: F3SZ-18813-A
$31.16 MSRP: $45.55
You Save: $14.39 (32%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Kit - Aerial
- Replaced by: MCPZ-18813-D
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2005 Ford Crown Victoria | 8 Cyl 4.6L | 4AT
View related parts
Ford Crown Victoria Aerial Assembly
Part Number: 9G1Z-15603-A
$68.85 MSRP: $85.00
You Save: $16.15 (19%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Aerial Assy
- Replaced by: DL3Z-15603-C
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2008-2011 Ford Crown Victoria | 8 Cyl 4.6L Romeo SOHC EFI | 4-Speed Automatic Transmission 4R75E Livonia, Left Hand Drive, Rear-Wheel Drive (Left Hand Drive)
View related parts
Ford Crown Victoria Aerial Assembly
Part Number: 2W7Z-15603-AA
Product Specifications
- Other Name: Aerial Assy
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2002-2011 Ford Crown Victoria | 8 Cyl 4.6L, 8 Cyl 4.6L Romeo SOHC EFI | 4AT, 4AT 4R70W, 4AT 4R75W, 4-Speed Automatic Transmission 4R75E Livonia, Left Hand Drive, Rear-Wheel Drive (Left Hand Drive)
View related parts
Ford Crown Victoria Rod Assembly - Replacement - Aerial
Part Number: F3AZ-18A886-A
Product Specifications
- Other Name: Antenna Mast, Mast
- Manufacturer Note: Power radio antenna,includes mast & installation sketch,stainless steel
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 1992-1994 Ford Crown Victoria | 8 Cyl 4.6L | 4AT AOD, 4AT AOD-E

Ford Crown Victoria Antenna

The Ford Crown Victoria Antenna allows the sedan to receive AM and FM broadcasts clearly to keep drivers informed and entertained. The early Ford Crown Victoria models were installed with a long telescoping Antenna made from thin steel tubing mounted near the hood. Owners had to lower the Antenna manually before squeezing into their low garages. In a bid to improve radio tech, Ford retained the familiar fender position but switched to a smaller mast Antenna that connects to the receiver via wiring and a small in-line amplifier for radio-frequency signals. Later editions of the Crown Victoria periodically integrated a glass-embedded Antenna within the windshield or rear window, which reduced wind noise and still picked up distant radio stations. Although an industry trend noted the arrival of roof satellite units with digital clarity, the company was dependent on its tried-and-tested designs as every Ford sedan that includes even the enduring Crown Victoria uses its Antenna whether with an external mast or a hidden strip to convert invisible waves into the music, news, and traffic updates that make routine journeys connected drives.

We provide a wide range of Ford Crown Victoria Antenna at the optimal prices. If you need Ford Crown Victoria Antenna, you can shop with confidence on our website. All our OEM parts come with a manufacturer's warranty and are delivered to your doorstep with a fast delivery service.

Ford Crown Victoria Antenna Parts Questions & Experts Answers

Aerial Kit
5C3Z-18813-AA
Q: How to perform a resistance check and replace the antenna on Ford Crown Victoria?
A:
To perform a resistance check, ensure the antenna cable is installed on the vehicle and unplugged from the radio, then use an ohmmeter to check the antenna between the cable and tip, expecting a reading of less than 5 ohms; if the reading is higher, replace the antenna and cable assembly. For replacement, first disconnect the cable from the negative battery terminal. For a power antenna, lower the antenna, remove the rear screws from the right side front splash shield for access, and take out the lower antenna bolt. Next, remove the nut at the top of the antenna stanchion and lower the antenna through the fender opening, using needle nose pliers to unscrew the antenna stanchion nut. Installation follows the reverse order of removal. For a manual antenna, detach the antenna lead retaining clips in the engine compartment, remove the screws, and detach the right cowl side trim panel. Then, remove the radio and unplug the antenna lead cable, take off the radio antenna base cap, remove the mounting screws, and pull the base and cable assembly through the fender opening into the engine compartment, with installation again being the reverse of removal.