How to remove and install an antenna and antenna cable on the Mercury Mariner?

Remove the antenna mast with a 10 mm wrench from its mounting base. Remove The Right scuff plate and right lower A-pillar trim panel. Working Under the right end of the dash, detach the two antenna cable clips and disconnect the antenna cable connector. Loosen The right front wheel lug nuts. Raise the vehicle and place it securely on jackstands. Remove the right front wheel. Remove the right inner fender splash shield. Working inside the fender area, remove the antenna cable grommet, pull the antenna cable into the fender area, remove the antenna support bracket nut, then pull the antenna mounting base down through its hole in the fender and remove the mounting base, support bracket and antenna as a single assembly. Remove The Electrical tape securing the antenna cable to the support bracket and discard the old antenna base and cable. Installation Is the reverse of removal. Remove the radio. Remove the right scuff plate and kick panel, then disconnect the inside part of the antenna cable from the outside cable. Remove the glove box. Detach the three pin-type retainers that secure the cable to the horizontal support brace located on the lower edge of the glove box recess. There are two more pin-type retainers securing the antenna cable to the vertical support brace that's located on the right side of the radio recess. Detach both of them. Remove the inside antenna cable. Installation is the reverse of removal.

Genuine Mercury Mariner Antenna Cable

Radio Antenna Cable

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

5 Antenna Cables found

View related parts
Mercury Mariner Extension Cable Assembly
Part Number: YL8Z-18812-AA
$15.51 MSRP: $21.19
You Save: $5.68 (27%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Cable Assy - Extension; Antenna Cable, Cable
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2005-2007 Mercury Mariner | 4 Cyl 2.3L, 4 Cyl 2.3L Hybrid Gas/Electric DOHC, 6 Cyl 3.0L DOHC EFI Modular | 4AT CD4E, 5-Speed Manual Transmission, 5-Speed Manual Transmission - AK, 6-Speed Automatic Transmission 6F Mid-Range, CVT Auto Trans Powersplit Elec, Four-Wheel Drive (Full Time) (Left Hand Drive), Front-Wheel Drive (Left Hand Drive), Left Hand Drive, Two-Wheel Drive (Left Hand Drive)
View related parts
Mercury Mariner Extension Cable Assembly
Part Number: 8L8Z-18812-C
$23.51 MSRP: $33.48
You Save: $9.97 (30%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Cable Assy - Extension; Antenna Cable, Cable
- Manufacturer Note: BLACK
- Replaces: 8L8Z-18812-B, 8L8Z-18812-A
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2008-2011 Mercury Mariner | 4 Cyl 2.3L, 4 Cyl 2.3L Hybrid Gas/Electric DOHC, 4 Cyl 2.5L Duratec (110kW/150PS), 4 Cyl 2.5L PFI Gas/Electric, 6 Cyl 3.0L DOHC EFI Modular, 6 Cyl 3.0L OHC Duratec | 4AT CD4E, 5-Speed Manual Transmission - AK, 6-Speed Automatic Transmission 6F Mid-Range, CVT Auto Trans Powersplit Elec, Four-Wheel Drive (Full Time) (Left Hand Drive), Front-Wheel Drive (Left Hand Drive), Left Hand Drive
View related parts
Mercury Mariner Extension Cable Assembly
Part Number: 8L8Z-18812-B
$23.51 MSRP: $33.48
You Save: $9.97 (30%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Cable Assy - Extension
- Manufacturer Note: BLACK
- Replaced by: 8L8Z-18812-C
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2008-2010 Mercury Mariner | 4 Cyl 2.3L, 4 Cyl 2.3L Hybrid Gas/Electric DOHC, 4 Cyl 2.5L Duratec (110kW/150PS), 4 Cyl 2.5L PFI Gas/Electric, 6 Cyl 3.0L DOHC EFI Modular, 6 Cyl 3.0L OHC Duratec | 4AT CD4E, 5-Speed Manual Transmission - AK, 6-Speed Automatic Transmission 6F Mid-Range, CVT Auto Trans Powersplit Elec, Four-Wheel Drive (Full Time) (Left Hand Drive), Front-Wheel Drive (Left Hand Drive), Left Hand Drive
View related parts
Mercury Mariner Extension Cable Assembly
Part Number: 8L8Z-18812-A
$23.51 MSRP: $33.48
You Save: $9.97 (30%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Cable Assy - Extension
- Manufacturer Note: BLACK
- Replaced by: 8L8Z-18812-C
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2008 Mercury Mariner | 4 Cyl 2.3L, 4 Cyl 2.3L Hybrid Gas/Electric DOHC, 6 Cyl 3.0L DOHC EFI Modular | 4AT CD4E, 5-Speed Manual Transmission - AK, 6-Speed Automatic Transmission 6F Mid-Range, CVT Auto Trans Powersplit Elec, Four-Wheel Drive (Full Time) (Left Hand Drive), Front-Wheel Drive (Left Hand Drive), Left Hand Drive
View related parts
Mercury Mariner Extension Cable Assembly
Part Number: YL8Z-18812-DA
Product Specifications
- Other Name: Cable Assy - Extension
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2007 Mercury Mariner | 4 Cyl 2.3L, 4 Cyl 2.3L Hybrid Gas/Electric DOHC, 6 Cyl 3.0L DOHC EFI Modular | 4AT CD4E, 5-Speed Manual Transmission - AK, 6-Speed Automatic Transmission 6F Mid-Range, CVT Auto Trans Powersplit Elec, Four-Wheel Drive (Full Time) (Left Hand Drive), Front-Wheel Drive (Left Hand Drive), Left Hand Drive

Mercury Mariner Antenna Cable

The Mercury Mariner Antenna Cable channels radio wave energy from the vehicle antenna to the receiver, giving drivers clear AM and FM sound on every trip. Running between mast and dashboard unit, this Antenna Cable mates with the built in amplifier so the radio can strengthen weak broadcasts. Depending on model year, Mercury Mariner crossovers have relied on three antenna layouts, each still linked to the same Antenna Cable. An internal antenna hides in the windshield, safeguarding it from car wash damage yet still requiring the cable to snake behind trim panels. The external whip, a metal or fiberglass rod by the hood, attaches to the Antenna Cable through the fender, offering easy access but higher risk of snaps or bends. Mariner roof mounted satellite units pair with the identical cable to deliver crisper digital signals, especially in remote zones. Every Mercury edition uses the same Antenna Cable route, so swaps stay familiar to Mercury owners and first time Mariner drivers alike.

We provide a wide range of Mercury Mariner Antenna Cable at the optimal prices. If you need Mercury Mariner Antenna Cable, you can shop with confidence on our website. All our OEM parts come with a manufacturer's warranty and are delivered to your doorstep with a fast delivery service.

Mercury Mariner Antenna Cable Parts Questions & Experts Answers

Extension Cable Assembly
YL8Z-18812-DA
Q: How to remove and install an antenna and antenna cable on the Mercury Mariner?
A:
Remove the antenna mast with a 10 mm wrench from its mounting base. Remove The Right scuff plate and right lower A-pillar trim panel. Working Under the right end of the dash, detach the two antenna cable clips and disconnect the antenna cable connector. Loosen The right front wheel lug nuts. Raise the vehicle and place it securely on jackstands. Remove the right front wheel. Remove the right inner fender splash shield. Working inside the fender area, remove the antenna cable grommet, pull the antenna cable into the fender area, remove the antenna support bracket nut, then pull the antenna mounting base down through its hole in the fender and remove the mounting base, support bracket and antenna as a single assembly. Remove The Electrical tape securing the antenna cable to the support bracket and discard the old antenna base and cable. Installation Is the reverse of removal. Remove the radio. Remove the right scuff plate and kick panel, then disconnect the inside part of the antenna cable from the outside cable. Remove the glove box. Detach the three pin-type retainers that secure the cable to the horizontal support brace located on the lower edge of the glove box recess. There are two more pin-type retainers securing the antenna cable to the vertical support brace that's located on the right side of the radio recess. Detach both of them. Remove the inside antenna cable. Installation is the reverse of removal.