How to replace rear bearing on Lincoln Navigator?

Remove the axleshaft and the oil seal. A bearing puller which grips the bearing from behind will be required for this job. These tools, adapted to screw onto slide hammers, are available from tool stores and many auto parts stores. Attach a slide hammer to the puller and extract the bearing from the axle housing. Clean out the bearing recess and drive in the new bearing with a bearing installer or a piece of pipe positioned against the outer bearing race. Make sure the bearing is tapped in to the full depth of the recess and the numbers on the bearing are visible from the outer end of the axle housing. Install a new oil seal, then install the axleshaft.

How do you inspect and repack front wheel bearings on Lincoln Navigator?

To inspect and repack front wheel bearings, start by securely supporting the vehicle on jackstands. Spin each wheel to check for noise, resistance, and freeplay. If there's movement, inspect the bearings. Remove the wheel, caliper, and dust cap. Remove the cotter pin, nut lock, nut, and washer. Pull the hub/disc assembly to remove the outer bearing, then remove the assembly. Pry the seal out and remove the inner bearing. Clean and inspect all parts for wear or damage. Pack the bearings with high-temperature grease. Apply grease to the spindle and hub. Place the bearings, seal, and washer in position. Install the spindle nut, tighten while spinning the hub, then loosen and hand-tighten. Install the nut lock and cotter pin. Install the dust cap, caliper, wheel, and lug nuts. Lower the vehicle and tighten the lug nuts.

Genuine Lincoln Navigator Wheel Bearing

Hub Bearing

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

11 Wheel Bearings found

View related parts
Lincoln Navigator Bearing
Part Number: 2L1Z-4B413-AA
$25.96 MSRP: $37.95
You Save: $11.99 (32%)
Ships in 1 Business Day
ADD TO CART
Product Specifications
- Other Name: Axle Bearing
- Manufacturer Note: Bearing asy. (axle housing) - pilot
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2003-2024 Lincoln Navigator | 6 Cyl 3.5 L GAS, 6 Cyl 3.5L GTDI, 8 Cyl 5.4L, 8 Cyl 5.4L DOHC EFI | 10-Speed Automatic Transmission (10R80), 4-Speed Automatic Transmission E4OD(4R100), 6-Speed Automatic Transmission (6R80), 6-Speed Automatic Transmission ZF 6HP26 Steptronic, Four-Wheel Drive (Part Time) (Left Hand Drive), Left Hand Drive, Rear-Wheel Drive (Left Hand Drive)
View related parts
Lincoln Navigator Bearing Assembly - Wheel
Part Number: 7L1Z-1104-BA
$208.19 MSRP: $347.27
You Save: $139.08 (41%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Bearing Assy - Wheel Hub
- Replaced by: 7L1Z-1104-G
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2007-2009 Lincoln Navigator | 8 Cyl 5.4L | 4-Speed Automatic Transmission E4OD(4R100), 6-Speed Automatic Transmission (6R80), 6-Speed Automatic Transmission ZF 6HP26 Steptronic, Left Hand Drive, Rear-Wheel Drive (Left Hand Drive)
View related parts
Lincoln Navigator HUB ASY - WHEEL
Part Number: JL1Z-1104-G
$388.77 MSRP: $556.36
You Save: $167.59 (31%)
ADD TO CART
Product Specifications
- Other Name: Front Hub & Bearing, Hub & Bearing
- Replaces: JL1Z-1104-E, HUB-384, JL1Z-1104-F, HUB-434, HUB-491, JL1Z-1104-C, JL1Z-1104-A, HUB-492
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2018-2021 Lincoln Navigator | 6 Cyl 3.5 L GAS, 6 Cyl 3.5L GTDI | 10-Speed Automatic Transmission (10R80), Four-Wheel Drive (Part Time) (Left Hand Drive), Left Hand Drive
View related parts
Lincoln Navigator HUB ASY - WHEEL
Part Number: JL1Z-1104-K
$350.30 MSRP: $563.64
You Save: $213.34 (38%)
ADD TO CART
Product Specifications
- Other Name: Front Hub & Bearing, Hub & Bearing
- Replaces: JL1Z-1104-H, JL1Z-1104-J, HUB-494, HUB-385, JL1Z-1104-B, HUB-495, JL1Z-1104-D, HUB-438
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2018-2021 Lincoln Navigator | 6 Cyl 3.5 L GAS, 6 Cyl 3.5L GTDI | 10-Speed Automatic Transmission (10R80), Left Hand Drive, Rear-Wheel Drive (Left Hand Drive)
View related parts
Lincoln Navigator Wheel Hub Assembly
Part Number: JL1Z-1109-A
$308.49 MSRP: $496.36
You Save: $187.87 (38%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Hub Assembly - Wheel; Hub & Bearing, Hub Assembly
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2018-2021 Lincoln Navigator | 6 Cyl 3.5 L GAS, 6 Cyl 3.5L GTDI | 10-Speed Automatic Transmission (10R80), Four-Wheel Drive (Part Time) (Left Hand Drive), Left Hand Drive, Rear-Wheel Drive (Left Hand Drive)
View related parts
Lincoln Navigator Wheel Hub Assembly
Part Number: JL1Z-1109-C
$301.71 MSRP: $485.45
You Save: $183.74 (38%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Hub Assembly - Wheel; Hub & Bearing, Hub Assembly
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2022-2024 Lincoln Navigator | 6 Cyl 3.5 L GAS
View related parts
Lincoln Navigator HUB ASY - WHEEL
Part Number: NL1Z-1104-B
$355.95 MSRP: $572.73
You Save: $216.78 (38%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Front Hub & Bearing, Hub & Bearing
- Replaced by: NL1Z-1104-D
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2022-2024 Lincoln Navigator | 6 Cyl 3.5 L GAS
View related parts
Lincoln Navigator HUB ASY - WHEEL
Part Number: ML3Z-1104-G
$326.57 MSRP: $525.45
You Save: $198.88 (38%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Front Hub & Bearing, Hub & Bearing
- Replaced by: ML3Z-1104-P
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2022-2023 Lincoln Navigator | 6 Cyl 3.5 L GAS
View related parts
Lincoln Navigator Kit - Wheel Bearing
Part Number: 6L1Z-1A049-AA
Product Specifications
- Other Name: Kit - Wheel Bearing Repair
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2006 Lincoln Navigator | 8 Cyl 5.4L | 4-Speed Automatic Transmission E4OD(4R100), 6-Speed Automatic Transmission (6R80), 6-Speed Automatic Transmission ZF 6HP26 Steptronic, Four-Wheel Drive (Part Time) (Left Hand Drive), Left Hand Drive, Rear-Wheel Drive (Left Hand Drive)
View related parts
Lincoln Navigator Bearing Assembly - Wheel
Part Number: 6L1Z-1104-A
Product Specifications
- Other Name: Bearing Assy - Wheel Hub
- Manufacturer Note: Service Kit
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2003-2006 Lincoln Navigator | 8 Cyl 5.4L, 8 Cyl 5.4L DOHC EFI | 4-Speed Automatic Transmission E4OD(4R100), 6-Speed Automatic Transmission (6R80), 6-Speed Automatic Transmission ZF 6HP26 Steptronic, Left Hand Drive, Rear-Wheel Drive (Left Hand Drive)
View related parts
Lincoln Navigator Kit - Wheel Bearing Repair
Part Number: 2L1Z-1A049-AA
Product Specifications
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2003-2005 Lincoln Navigator | 8 Cyl 5.4L, 8 Cyl 5.4L DOHC EFI | 4-Speed Automatic Transmission E4OD(4R100), 6-Speed Automatic Transmission (6R80), 6-Speed Automatic Transmission ZF 6HP26 Steptronic, Four-Wheel Drive (Part Time) (Left Hand Drive), Left Hand Drive, Rear-Wheel Drive (Left Hand Drive)

Lincoln Navigator Wheel Bearing

The Wheel Bearing of Lincoln Navigator vehicles are Specifically vital parts that enable the wheels to rotate in a manner that can support performance and safety. Thus, depending on the specific assembly, there are 3 types of application of hubs and bearings: The most common is the unit assembly, which incorporates the sensor of ABS. Defective bearings which can include worn out or loose ones, lead to noise and vibrations, which can in turn lead to loss of wheels. To check for problems, spin the wheel, look for roughness to the touch, and check play with a dial indicator. A lot of attention has to be paid to tapered roller bearings, which are to be replaced when worn-out: it is necessary to clean them and grease them adequately. In conclusion, Wheel Bearings are very essential when it comes to the smooth performance as well as safe driving of Lincoln Navigator vehicles.

We provide a wide range of Lincoln Navigator Wheel Bearing at the best prices possible. If you need Lincoln Navigator Wheel Bearing, you can shop with confidence on our website. All our OEM parts come with a manufacturer's warranty and are delivered to your door step with a fast delivery service.

Lincoln Navigator Wheel Bearing Parts Questions & Experts Answers

Bearing Assembly - Wheel
7L1Z-1104-BA
Q: How to replace rear bearing on Lincoln Navigator?
A:
Remove the axleshaft and the oil seal. A bearing puller which grips the bearing from behind will be required for this job. These tools, adapted to screw onto slide hammers, are available from tool stores and many auto parts stores. Attach a slide hammer to the puller and extract the bearing from the axle housing. Clean out the bearing recess and drive in the new bearing with a bearing installer or a piece of pipe positioned against the outer bearing race. Make sure the bearing is tapped in to the full depth of the recess and the numbers on the bearing are visible from the outer end of the axle housing. Install a new oil seal, then install the axleshaft.
Kit - Wheel Bearing Repair
2L1Z-1A049-AA
Q: How do you inspect and repack front wheel bearings on Lincoln Navigator?
A:
To inspect and repack front wheel bearings, start by securely supporting the vehicle on jackstands. Spin each wheel to check for noise, resistance, and freeplay. If there's movement, inspect the bearings. Remove the wheel, caliper, and dust cap. Remove the cotter pin, nut lock, nut, and washer. Pull the hub/disc assembly to remove the outer bearing, then remove the assembly. Pry the seal out and remove the inner bearing. Clean and inspect all parts for wear or damage. Pack the bearings with high-temperature grease. Apply grease to the spindle and hub. Place the bearings, seal, and washer in position. Install the spindle nut, tighten while spinning the hub, then loosen and hand-tighten. Install the nut lock and cotter pin. Install the dust cap, caliper, wheel, and lug nuts. Lower the vehicle and tighten the lug nuts.