How to remove and install the Front Door Striker and Rear Door Striker, and what adjustments can be made on Ford Ranger?

To remove the door latch striker stud from the door jamb, use a Torx bit to unscrew it, and for installation, reverse the removal process, making adjustments as necessary. The door latch striker can be adjusted both vertically and laterally, as well as fore and aft, but it should not be used to compensate for door misalignment. Shimming may be applied to achieve the correct clearance between the latch and the striker, ensuring that no more than one shim is used per door. To check the clearance, apply a layer of dark grease on the striker, then open and close the door several times to observe the pattern left in the grease. Adjust the door striker assembly laterally to ensure a flush fit at the door and pillar or at the quarter panel, and securely tighten the door latch striker once adjustments are complete.

Genuine Ford Ranger Front Door Striker

Front Door Lock Striker

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

5 Front Door Strikers found

View related parts
Ford Ranger Door Locking Mechanism Striker
Part Number: 8F9Z-5422008-A
$32.87 MSRP: $42.77
You Save: $9.90 (24%)
ADD TO CART
Product Specifications
- Other Name: Striker - Door Locking Mechanism; Striker
- Position: Passenger Side/Driver Side
- Replaced by: 5F9Z-5422008-AA
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2008-2011 Ford Ranger | 4 Cyl 2.3L NA Petrol, 6 Cyl 3.0L OHV EFI, 6 Cyl 4.0L SOHC EFI | 5-Speed Automatic Transmission - 5R44E/5R55E, 5-Speed Manual Transmission - R1HD, 5-Speed Manual Transmission M5R1, Four-Wheel Drive (Part Time) (Left Hand Drive), Left Hand Drive, Rear-Wheel Drive (Left Hand Drive)
View related parts
Ford Ranger Striker - Door Locking
Part Number: F37Z-1022008-A
$32.87 MSRP: $42.77
You Save: $9.90 (24%)
ADD TO CART
Product Specifications
- Other Name: STRIKER - DOOR LOCKI
- Manufacturer Note: RH and LH - front doors
- Position: Passenger Side And Driver Side
- Replaced by: 5F9Z-5422008-AA
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 1993-1997 Ford Ranger | 4 Cyl 2.3L, 6 Cyl 3.0L, 6 Cyl 4.0L | 4AT 4R44E, 4AT 4R55E, 4AT A4LD, 5AT 5R55E, 5MT
View related parts
Ford Ranger Striker - Door Locking
Part Number: E9FZ-5822008-A
$46.03 MSRP: $66.72
You Save: $20.69 (32%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: STRIKER - DOOR LOCKI
- Position: Passenger Side And Driver Side
- Replaced by: F67Z-7822008-AA
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 1983-1991 Ford Ranger | 4 Cyl 2.0L, 4 Cyl 2.2L, 4 Cyl 2.3L, 6 Cyl 2.8L, 6 Cyl 2.9L, 6 Cyl 3.0L, 6 Cyl 4.0L | 3AT C3, 3AT C5, 4AT A4LD, 4MT, 5MT
View related parts
Ford Ranger STRIKER - DOOR LOCKING MECHANI
Part Number: JX7Z-5822008-C
$11.74 MSRP: $16.72
You Save: $4.98 (30%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Striker
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2024-2025 Ford Ranger | 4 Cyl 2.3 L GAS, 6 Cyl 2.7 L GAS, 6 Cyl 3.0 L GAS
View related parts
Ford Ranger PANEL - FULL PARTITION
Part Number: AB3Z-21265A04-A
$48.00 MSRP: $68.97
You Save: $20.97 (31%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Lower Striker, Striker
- Manufacturer Note: RH/LH
- Position: Passenger Side/Driver Side
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2019-2023 Ford Ranger | 4 Cyl 2.3 L GAS, 4 Cyl 2.3L TIVCT DI TC | 10-Speed Automatic Transmission (10R80), 2 Whl L/H Rear Drive-High Ride, Four-Wheel Drive (Part Time) (Left Hand Drive), Left Hand Drive

Ford Ranger Front Door Striker

The Ford Ranger Front Door Striker helps to keep your pickup's door aligned and firmly latched so you don't get slamming or rattling noises. The small U-shaped piece of metal rests against the latch while the door is closed. The latch hooks around the Front Door Striker, keeping the door closed and stopping vibration. Through years of constant opening and closing, the hinge bushings can wear and the Front Door Striker can shift, causing the door to sag or not catch. If that happens, loosen the screws, tap the part with a hammer, and then retighten. You should have a smooth closure once again. It is straightforward to replace a worn Front Door Striker with some basic hand tools and a pencil mark for location that will take about 15 minutes. However, precise alignment is critical so that the latch meets squarely on the striker. A sturdy zinc-coated Front Door Striker will last long. Through light cleaning and lubricant twice yearly, you can maintain this operation, which will give any Ford Ranger door that crisp factory click, help the Ranger driver avoid frustration, and match the Ford standard to keep every Ranger feeling solid while satisfying Ford owners.

We provide a wide range of Ford Ranger Front Door Striker at the optimal prices. If you need Ford Ranger Front Door Striker, you can shop with confidence on our website. All our OEM parts come with a manufacturer's warranty and are delivered to your doorstep with a fast delivery service.

Ford Ranger Front Door Striker Parts Questions & Experts Answers

Door Locking Mechanism Striker
8F9Z-5422008-A
Q: How to remove and install the Front Door Striker and Rear Door Striker, and what adjustments can be made on Ford Ranger?
A:
To remove the door latch striker stud from the door jamb, use a Torx bit to unscrew it, and for installation, reverse the removal process, making adjustments as necessary. The door latch striker can be adjusted both vertically and laterally, as well as fore and aft, but it should not be used to compensate for door misalignment. Shimming may be applied to achieve the correct clearance between the latch and the striker, ensuring that no more than one shim is used per door. To check the clearance, apply a layer of dark grease on the striker, then open and close the door several times to observe the pattern left in the grease. Adjust the door striker assembly laterally to ensure a flush fit at the door and pillar or at the quarter panel, and securely tighten the door latch striker once adjustments are complete.