My Garage
My Account
Cart
Genuine Ford Bronco II Fuel Injector
Gas Injector- Select Vehicle by Model
- Select Vehicle by VIN
Select Vehicle by Model
orMake
Model
Year
Select Vehicle by VIN
For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).
5 Fuel Injectors found
Ford Bronco II Fuel Injector
Specifically, The Fuel Injector is an important component in Ford Bronco II cars as it how it sprays fuel into the engine cylinders to create an air-fuel mixture that would ignite easily. This system is governed by the Engine Control Module (ECM) and with reference to the engine load, this dictates the timing and quantity of fuel injected. Returnless fuel injection system is used in Ford Bronco II models and this system of fuel injection entails the following features of the system; It helps to avoid such problems related to standard systems, as fuel pressure regulators, and the return line. But the fuel injectors are not immune to failure and this can results in poor performance, less power, and high emission. It is relevant to perform timely replacements of faulty injectors as well as give general maintenance to the injectors so that the performance of the vehicles will not be affected as well as to avoid instances where there are damages in the engine.
We provide a wide range of Ford Bronco II Fuel Injector at the best prices possible. If you need Ford Bronco II Fuel Injector, you can shop with confidence on our website. All our OEM parts come with a manufacturer's warranty and are delivered to your door step with a fast delivery service.
Ford Bronco II Fuel Injector Parts Questions & Experts Answers
- Q: How do I remove and install fuel injectors and the fuel rail in gasoline engine on my Ford Bronco II?A:Remove the upper intake manifold. Depressurize the fuel system, disconnect the fuel lines, remove fuel supply and return line clips, detach the vacuum from the regulator of fuel pressure, disconnect fuel chassis inlet and outlet hoses. Disconnect the fuel injector wire harness plugs by labeling them. Remove fuel rail bolts. Disengage the fuel rail assembly from the injectors and remove injectors from intake manifold. Place these components on a clean surface. Examine injector O-rings for damage: replace them if necessary. Make sure that injector caps are clean. Lubricate O-rings with engine oil. Install these injectors into this rail of its gasoline. Position a new gasket of a fuel rail. Install this assembly into a lower intake manifold. Push down to seat O-rings. Tighten retaining bolts. Connect those two-line gas hoses. Attach that other vacuum tube to regulator. Connect injector wiring harnesses' connectors again. Plug in that one vacuum hose to regulator too. Then put back this air intake system together with throttle body. As for any leaks check or not. Besides, test these injectors using DVOM. Don't forget to unplug this connector of a wiring harness!
- Q: How to remove and install fuel injectors in diesel engine on Ford Bronco II?A:Disconnect both battery ground cables for the 2.2L engine. Disconnect and remove the injection lines from the nozzles and injection pump, capping all lines and fittings. Remove the fuel return line and gaskets, and the bolts attaching the fuel line heater clamp to the cylinder head, positioning the heater out of the way. Remove the nozzles using a 27mm deepwell socket, and the nozzle washer (copper) and nozzle gasket (steel) using Tool T71P-19703-C or equivalent. Clean the nozzle assemblies with Nozzle Cleaning Kit, Rotunda 14-0301 or equivalent, and a suitable solvent, drying thoroughly. Clean the nozzle seats in the cylinder head with Nozzle Seat Cleaner, T83T-9527-B or equivalent. Position the new nozzle washers and gaskets in the nozzle seats, install the nozzles and tighten. Install the nozzle gaskets with blue side face up (toward nozzle). Position the fuel line heater clamps and install attaching bolts. Install the fuel return line with new gaskets on nozzles. Install the injection lines on the nozzles and injection pump and tighten the line nuts. Connect both battery ground cables. Run the engine and check for fuel leaks.For the 2.3L engine, disconnect battery ground cables from both batteries. Disconnect and remove injection lines from injection nozzles and injection pump, capping all lines and fittings using Protective Cap Set, T85T- 9395-A, or equivalent. Remove fuel return pipe and gaskets. Remove nozzles using a 21mm deep well socket. Remove holder gasket and nozzles gasket using 0-ring Tool T71P-19703-C or equivalent. Clean exterior of nozzle assemblies using brass brush from Nozzle Clean Kit 014-00301, or equivalent and a suitable solvent, drying thoroughly. Install new nozzle gasket and holder gasket in cylinder. Install nozzles and tighten to specification, using a 21mm deep well socket. Install fuel return pipe using new gaskets. Tighten nuts to specification. Install injection lines on nozzle and fuel injection pump and tighten line nuts to specification. Connect battery ground cables to both batteries. Run engine and check for fuel leaks.
